DSC HS-TE1650 - Installation Manual - English - Concourse 1x6 Analog Bridged Telecom Expansion Module

File Preview
File Preview
Click below to download for free

Text Preview

Warranty Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product be free of defects in materials and workmanship under normal use and that in fulfilment of any breach such warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment return of the equipment to its repair depot This warranty applies only to defects in parts and and not to damage incurred in shipping or handling or damage due to causes beyond the of Digital Security Controls Ltd such as lightning excessive voltage mechanical shock water damage damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Controls Ltd Digital Security Controls Ltd neither assumes responsibility for nor authorizes any person purporting to act on its behalf to modify or to change this warranty nor to assume for it any warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested a regular basis However despite frequent testing and due to but not limited to criminal or electrical disruption it is possible for this product to fail to perform as expected INFORMATION Changes or modifications not expressly approved by Digital Security Ltd could void the user authority to operate this equipment Digital Security Controls Ltd Canada 1 800 387 3630 www dsc com in Canada 29005813 R001 6 Port Expansion Module Instructions HS TE1650 is an Analog Telecom Expansion Module for use with the DSC Home Wiring Systems solution The HS TE1650 features an RJ 45 input for up to 4 incoming lines six RJ 45 jacks for connecting outlets to the system and RJ 45 jack as an expansion output connector The HS TE1650 is designed for use the HS TH1600 1 x 6 Telecom Distribution Module of Package installing the module confirm that the package contains the following parts one HS TE1650 Analog Telecom Expansion Card one HS MP200 mounting plate seven plastic standoffs Instructions Insert the standoffs into the HS MP200 mounting plate as per Figure A matching hole pattern on the HS TE1650 Telecom Expansion module Plate Mounting A Align the HS TE1650 Telecom Expansion module over the standoffs and snap into place Find a suitable mounting location for the HS TE1650 Telecom Expansion module the cabinet The recommended location is below the HS TH1600 HS TE1650 Telecom Expansion modules can be added below the first Align the two mounting tabs with the holes in wire raceway and insert as per Figure B Snap the module into place by pushing the opposite side towards the back of the B Instructions Incoming Telecom Service Cable s Using a CAT5 patch cord of sufficient length plug one end into the LINE OUT of the HS TH1600 If there is another HS TE1650 already installed plug one of the patch cord into the LINE OUT jack of this HS TE1650 Plug the other into the LINE IN jack of the HS TE1650 being installed Test all connections to confirm proper installation and termination Outlet Cables Home run CAT5 cable to each desired telecom location and route the cables into cabinet through the raceway to the HS TE1650 Telecom Expansion module sufficient length at both ends of the run to avoid stress and for proper and trim out Label each cable at both ends for easier identification Terminate each CAT5 drop at the desired location using an RJ 45 keystone jack to TIA 568A standard observing proper CAT5 wiring practices Trim out the appropriate wall plate If using a multiple wall outlet mark the telecom accordingly Terminate each CAT5 drop at the HS TE1650 Telecom Expansion module with an plug wired to TIA 568A standard and observing proper CAT5 wiring See Figure C Test all connections to confirm proper installation and termination This module is intended for use with Analog telephones and POTS Plain Old Service Any other use may cause improper operation of the connected All RJ 45 connectors are connected in parallel and therefore output can be made at any RJ 45 jack The RJ 45 LINE OUT jack is also in parallel to the output RJ 45 jacks providing a service expansion port All requirements for installation of CAT5 should be met for proper of connected equipment Do not strip off cable sheathing more than for proper termination Do not kink or knot cable Do not crush cable with ties Do not bend cable at right angles or any other sharp bends All cable should have a minimum of a 2 radius Do not untwist pairs more than Diagram IN 1 2 3 OUT 4 5 6 NEXT Security Controls Ltd in Canada KEYSTONE R T R 2 3 4 5 6 7 8 T R KEYSTONE Standard 1 Blue White Blue 2 Orange White Orange 3 Green White Green 4 Brown White Brown Coloured white is Tip and solid is Ring C Input Lines 4 Wiring Standard T568A Connections 6 Interfaces RJ 31X None Connection RJ 45 Connection RJ 45 Out Connection RJ 45 Instructions Incoming Telecom Service Cable s Using a CAT5 patch cord of sufficient length plug one end into the LINE OUT of the HS TH1600 If there is another HS TE1650 already installed plug one of the patch cord into the LINE OUT jack of this HS TE1650 Plug the other into the LINE IN jack of the HS TE1650 being installed Test all connections to confirm proper installation and termination Outlet Cables Home run CAT5 cable to each desired telecom location and route the cables into cabinet through the raceway to the HS TE1650 Telecom Expansion module sufficient length at both ends of the run to avoid stress and for proper and trim out Label each cable at both ends for easier identification Terminate each CAT5 drop at the desired location using an RJ 45 keystone jack to TIA 568A standard observing proper CAT5 wiring practices Trim out the appropriate wall plate If using a multiple wall outlet mark the telecom accordingly Terminate each CAT5 drop at the HS TE1650 Telecom Expansion module with an plug wired to TIA 568A standard and observing proper CAT5 wiring See Figure C Test all connections to confirm proper installation and termination This module is intended for use with Analog telephones and POTS Plain Old Service Any other use may cause improper operation of the connected All RJ 45 connectors are connected in parallel and therefore output can be made at any RJ 45 jack The RJ 45 LINE OUT jack is also in parallel to the output RJ 45 jacks providing a service expansion port All requirements for installation of CAT5 should be met for proper of connected equipment Do not strip off cable sheathing more than for proper termination Do not kink or knot cable Do not crush cable with ties Do not bend cable at right angles or any other sharp bends All cable should have a minimum of a 2 radius Do not untwist pairs more than Diagram IN 1 2 3 OUT 4 5 6 NEXT Security Controls Ltd in Canada KEYSTONE R T R 2 3 4 5 6 7 8 T R KEYSTONE Standard 1 Blue White Blue 2 Orange White Orange 3 Green White Green 4 Brown White Brown Coloured white is Tip and solid is Ring C

Related Files