
File preview
Click below to download immediately for free
File data
- Filename: 4163708295_DSC_HS-VT1680_-_Installation_Manual_-_English_-_Concourse_1x6_Analog_Bridged_Telecom_Expansion_Module_With_1x8_Passive_Video_Splitter.pdf
- File size: 796 KB
- File type: pdf
- Download count: 57
Text Preview
Warranty Security Controls Ltd. warrants that for a period of 12 months from the date of purchase, the shall be free of defects in materials and workmanship under normal use and that in fulfillment any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the equipment upon return of the equipment to its repair depot. This warranty applies only to in parts and workmanship and not to damage incurred in shipping or handling, or damage due to beyond the control of Digital Security Controls Ltd. such as lightning, excessive voltage, shock, water damage, or damage arising out of abuse, alteration or improper application of equipment. foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all warranties, whether expressed or implied and of all other obligations or liabilities on the part of Security Controls Ltd. Digital Security Controls Ltd. neither assumes responsibility for, nor any other person purporting to act on its behalf to modify or to change this warranty, nor to for it any other warranty or liability concerning this product. no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential dam- loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection the purchase, installation or operation or failure of this product. Digital Security Controls Ltd. recommends that the entire system be completely tested on regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or disruption, it is possible for this product to fail to perform as expected INFORMATION: Changes or modifications not expressly approved by Digital Secu- Controls Ltd. could void the user authority to operate this equipment. COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd. void your authority to use this equipment. equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable against harmful interference in a residential installation. This equipment generates, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is guarantee that interference will not occur in a particular installation. If this equipment does harmful interference to radio or television reception, which can be determined by turn- the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: the receiving antenna the separation between the equipment and receiver the equipment into an outlet on a circuit different from that to which the receiver connected. the dealer or an experienced radio/ TV technician for help. user may find the following booklet prepared by the FCC useful: to Identify and Radio/Television Interference Problems This booklet is available from the U.S. Gov- Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4. device complies with Part 15 of the FCC Rules. Operation is subject to the following two (1) This device may not cause harmful interference, and (2) this device must any interference received, including interference that may cause undesired operation. requirements for installation of CAT5 cable should be met for proper operation of connected Do not strip off cable sheathing more than required for proper termination. Do not or knot cable. Do not crush cable with cable ties. Do not bend cable at right angles or create other sharp bends. All cable bends should have a minimum of a 2″ radius. Do not untwist pairs more than 1/2 inch. requirements for installation of coaxial cable should be met for proper operation of connected Do not strip off cable sheathing more than required for proper termination. Do not or knot cable. Do not crush cable with cable ties. Do not bend cable at right angles or make other sharp bends. All cable bends should have a minimum of a 2 radius. telecom module is intended for use with analog telephones and POTS (Plain Old Telephone Any other use may cause improper operation of the connected equipment. All IDC con- (except IDC 1 Telephone Line In) are connected in para