DSC NT9201 - Installation Manual - English - French - Spanish - Envoy Remote Sounder for NT9010

File Preview
File Preview
Click below to download for free

Text Preview

NT9201 Sounder Installation Instructions distance les instructions d Channel de Cableado removing the top plastic and the printed circuit secure the back plastic housing the mounting surface using this slot a screw provided a screw in either of the slots the left or to the right of 2 in the top and bottom locations this is done and the unit is securely to the mounting location please replace the printed circuit board and top plastic housing the Remote Sounder can connect a hardwired remote sounder to the NT9010 system This provides an additional station for the NT9010 to sound alarms to system status and to allow central talk listen in sessions the remote sounder to the control unit as shown The can be connected up to 500ft away from the NT9010 using shielded cable the sounder to work on the system must turn on the Remote option section 017 5 When this option is turned the remote sounder will also be supervised If the NT9201 does not a supervisory signal within 30 seconds a Bell Trouble will generated and logged in the event buffer 2.3.13 Talk Listen in Programming from the NT9010 Installation Guide Current 12mA Current 170mA an Additional Sounding Device NT9201 has an on board 50mA output This dedicated output follows sounder activation Therefore when the sounder is active the output on and when sounder is idle the output is off This output is useful applications where an external siren is required To connect an additional separate power supply and relay are required Please refer to the System Installation Manual for information limitations regarding product use and function and information on the as to liability of the manufacturer Channel de Cableado avoir retir le couvercle du en plastique et la carte imprim replacer le fond du en plastique sur la base de en utilisant cette encoche et la fournie une vis dans l des la droite ou la gauche de aux deux endroits en haut et en bas fois que cela est fait et que l unit est bien fix sur sa base veuillez la carte circuit imprim et le couvercle du corps en plastique de l distance pouvez brancher un avertisseur distance c sur le syst NT9010 Cet fournit au NT9010 une station suppl pour annoncer les afin de faire conna l du syst ainsi que pour faire des sessions avec la station centrale l distance de contr NT9010 tel au dos Le NT9201 peut jusqu 500 pieds 152 m du l de fils blind de 22 que l fonctionne sur le vous devez activer l distance section 017 5 Lorsque cette option est activ distance est supervis Si le NT9201 ne rapporte pas de signal de l de 30 secondes un de l Distance est g et entr dans le registre d la rubrique 2.3.13 Programmation Parler du d du NT9010 en attente 12mA en alarme 170mA d avertisseur sonore additionnel NT9201 int une sortie de 50mA Cette sortie d suit l l sonore Par cons lorsque l sonore est actif sortie commute l actif et lorsque l est inactif la sortie est Cette sortie est tr utile lorsque par exemple une sir ext requise Si vous d brancher une sir suppl vous devez une alimentation et un relais s Veuillez vous r au Manuel d du Syst des informations sur les limites concernant l et le du produit et des informations sur les limites concernant la du fabricant Channel de Cableado sonoro remoto Instrucciones de Instalaci de remover la parte de la caja pl y el del circuito asegure la parte de la caja pl a la superficie montaje usando ranura y el provisto un tornillo en cualquiera las ranuras de la izquierda o la de 2 en ambas la superior y la ubicaci inferior vez que es realizado y la unidad es asegurada fijamente a la ubicaci montaje por favor vuelva a colocar el tablero del circuito y la parte anterior la caja pl del dispositivo sonoro remoto sistema NT9010 se puede conectar un dispositivo sonoro al El dispositivo ofrece al sistema una estaci suplementaria que servir para sonar alarmas y para el estado del sistema as como comunicaciones bidireccionales con estaci central el dispositivo sonoro remoto con unidad de mando de acuerdo con las atr El NT9201 puede ser hasta 500 pies 152 m desde NT9010 usando un cable blindado que el dispositivo sonoro pueda funcionar en el sistema debe activar opci de Anuncio Remoto secci 017 opci 5 Una vez esta opci el dispositivo sonoro remoto ser tambi supervisado caso de que el NT9201 no env una se de supervisi durante 30 se crea una falla de tipo de la Campana Remota y la de eventos almacena el evento tambi 2.3.13 Programaci de la comunicaci bidireccional Manual de Instalaci NT9010 en espera 12mA en alarma 170mA un Dispositivo de Sonido Adicional NT9201 tiene una salida de corriente integral de 50 mA Esta salida sigue activaci del sonador Por lo tanto cuando el sonador se activa la salida prende y cuando el sonador se desactiva la salida se apaga Esta salida para aplicaciones que requiren una sirena externa Para conectar una adicional se requieren una fuente de alimentaci y un rel adicionales Este manual contiene informaci sobre restricciones del uso y funcionamiento del producto e informaci sobre las tal como la responsabilidad del fabricante Todo el manual se leer cuidadosamente 29005161 R004 following are the part numbers to order the Power Supply Relay and equipment to drive the siren 1.5A Power Supply 80020016 Relay 80020113 US 80020005 Can 80020151 Int 40VA Transformer 88014222 US 88014218 Can Transformer 17000044 Int 4Ah Rechargeable Backup Battery 88008002 US 88000002 Can Int consult the following connection diagram for wiring information le num de pi commander pour l le relais et autre n pour d la sir Alimentation 1,5 A 80020016 RM1 RM1C 80020113 US 80020005 Can 80020151 Int 16,5 V 40 V A 88014222 US

Related Files