
File preview
Click below to download immediately for free
File data
- Filename: 4865123790_DSC_WT4911_installation_manual_29007530.pdf
- File size: 2 MB
- File type: pdf
- Download count: 61
Text Preview
WT4911 / WT8911 v1.0 Instructions, Instructions d Instrucciones de instalaci Instru de Instala di installazione, Installatiehandleiding, Installationsguide, Installasjonsinstruksjoner, Pokyny k instalaci, Instrukcja instalacji, Asennusohjeet, Fran Espa Italiano, Nederlands Norsk, Dansk, Suomi, The siren is listed for UL/ULC Residential Burglary applications and it is intended to annunciate only burglary alarm tones. The will sound a dual frequency sweeping tone for burglary alarms. Carbon Monoxide and Fire signal annunciation use have not been by UL/ULC. The LED strobe light is not intended for Hearing Impaired signaling. Two-Way Wireless Outdoor Installation Instructions this installation sheet along with the associated alarm system installatio n manual for instructions and programming details. All instructions specified within that must be observed. The WT4911/8911 is a two-way wireless outdoor siren. Siren and the strobe light are activated when an alarm condition is received via DSC protocol from a compatible, two-way enabled security panel (e.g., PC9155). The must be enrolled on the security panel before it can receive commands the panel for sounding alarms, strobe activation and communicating a required such as the WT4911/8911 status or the local outdoor temperature. The out- siren is capable of sounding different alarm cadences (e.g., carbon monoxide, con- burglary, pulsating fire, or temporal three fire), and bell squawks to suit the type command it receives. Up to four WT4911/8911 can be enrolled on the same security and supervised as separate units. To ensure two-way contact between the siren and security panel, the WT4911/8911 regularly sends supervisory signals to the security With each supervisory signal sent to the panel, the siren provides the outdoor tem- In addition, the WT4911/8911 monitors for the case and wall tamper switch and the battery state. In the event of a low battery or a tamper activation, the will transmit the appropriate signal to the security panel, and (if config- provide an audible and visual indication that a local event has occurred. NOTE: For listed applications the siren sounds a continuous tone. (max): 93% R.H. Frequency: 433.92 MHz, MHz (WT8911 only) Life: 3 years typical usage Signals-Output Level: >=85dB @ 3m D size 3.6V Lithium Thionyl Chloride (ER34615M-T1, Able) (DSC ordering number, control panels: PC9155-433/868, PC9155D-433/868, PC9155G-433/868 for WT8911 only) Only model WT4911 is UL and ULC listed for residential burglary Battery life has not been evaluated by UL and ULC. up the WT4911 WT4911 contains a battery that includes a feature called This feature the shelf life of the battery when it is not being used. Every WT4911 will need be before using the outdoor siren for the first time. Make sure to follow the steps below for a brand new battery on the unit or a battery is being replaced. The WT4911 could lose power prematurely if a new battery is not used. Hold the tamper switch closed before plugging the battery in. Plug in the battery AND continue to hold the tamper for 10 seconds before releasing it. Once the tamper is released, after the initial 10 seconds, the siren flashes the strobe Temperature: -40 to 70 (-40 to 158 Range for UL/ULC: -40 to 66 1.8lbs and IP rating: 34 Signals-Output Level: for CE [email protected] 1m several different patterns to indicate it is in depassivation mode. It can take a unit up to 30 minutes to fully depassivate. depassivation is complete, the stroble lights shut off completely and the siren starts beep 3 times every 5 seconds. Create a tamper and the WT4911 will go into a normal power up sequence with 6 beeps and flashes of the strobe lights. The WT4911 is ready to be enrolled on the system. If the battery is unplugged during depassivation and plugged back in 1 minute, the depassivation sequence will continue. Depassivation Sequence depassivation reaches 30 minutes the siren stops trying to de