Fire-Lite BEAMMMK Multi-mounting Kit for use with Reflective Projected Beam Smoke Detectors

File Preview
File Preview
Click below to download for free

Text Preview

INSTALLATION AND MAINTENANCE INSTRUCTIONS Kit for use with Reflective Projected Beam Smoke Detectors Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 This manual should be left with the owner user of this equipment 1 CEILINg MOUNT BRACKET ASSEMBLy DESCRIPTION BEAMMMK allows reflected beam detectors and reflectors to be mounted either a vertical wall or the ceiling The kit allows for additional alignment in cases where the detector and reflector cannot be mounted within of each other The kit includes the hardware necessary to mount either single transmitter receiver unit or a single reflector To mount the trans the surface mount kit BEAMSMK must also be used If the and the reflector require additional alignment range two are required The kit is not compatible with the long range reflector kit kit includes the following parts bracket bracket mount bracket inside mount bracket outside Description Wall mount bracket Horizontal adjustment screw ceiling 10 24 2 1 4 Horizontal adjustment screw wall 10 24 13 8 Washer plastic 10 Washer metal 10 Washer metal split lock 10 Hex nut 10 24 screw 10 24 1 2 screw 10 24 5 8 washer plastic washer metal wrench BRACKETS a ceiling or wall bracket so that when mounted the transmitter re and the reflector will have a clear line of sight between them ceiling bracket is composed of two parts that should be assembled with inside part between the ceiling and the outside part as shown in Figure 1 brackets should be mounted so that the slot in the front of each bracket facing the other bracket Mount the brackets only on solid structures of the To avoid unwanted alarms due to wall movement do not mount to walls such as sheet metal walls see Mounting Locations section of transmitter receiver manual for more details IN FRONT BRACKET AND WIRINg INSTRUCTIONS BEAMSMK accessory must be used with the transmitter receiver to pro wiring entry Refer to Figures 2 through 4 for this step Read the installation instructions of the beam detector to determine the size and number of wires to be used Drill the appropriate holes for the flexible conduit using the drill centers on either the sides or the back of the surface mount base See 2 for details Note that the top of the surface mount base contains bosses for the brackets used in the next step Conduit sizes 1 2 or 3 4 are acceptable Assemble the brackets to the surface mount base using the two 10 5 8 screws and two 10 split lock washers provided See Figure 3 for The screws should be fully tightened Assemble the bracket to the brackets using the two 10 24 screws and fender washers provided See Figure 3 for details The bracket should be assembled to the brackets so that the words NOT PAINT appear in the front of the assembly Tighten the screws almost snug The assembly should tilt freely in either direction The will be fully tightened later when the alignment is performed Insert the flange of the bracket into the keyed hole of the wall or ceil mount bracket Slide the bracket forward into position The surface base should now hang from the bracket Insert the correct screw and washer combination either wall or ceil mount through the slot and into the hole of the mounting bracket Tighten the screw until almost snug The assembly should still freely in both directions The screw will be fully tightened later the alignment is performed Pull the wiring and the flexible conduit through the drilled hole s At nut s not included to conduit fitting and tighten Be sure to leave enough wire to reach the transmitter receiver unit attached to the surface mount base Be sure to leave enough flexible so that the transmitter receiver unit can be adjusted to aim at the Attach the transmitter receiver unit securely to the base using the four 1 2 screws supplied with the BEAMSMK accessory Adjust the transmitter receiver unit so that it is aiming directly at the Once aimed correctly fully tighten both vertical and horizontal screws For proper operation of the beam detector it must be securely mounted ensure no subsequent movement of the beam detector will occur after the is completed See Placement and Mounting sections of beam detector manual for further details Complete the installation of the transmitter receiver unit using the instruc included with the beam detector Test the system as indicated in the beam detector instructions INSTRUCTIONS REFLECTOR to Figure 4 for this step Assemble the brackets to the reflector using the two 10 24 5 8 two 10 split lock washers and two 10 locknuts provided See 4 for details The screws should be fully tightened Assemble the bracket to the brackets using the two 10 24 screws and fender washers provided See Figure 4 for details The bracket should be assembled to the brackets so that the words NOT PAINT appear in the front of the assembly Tighten the screws almost snug The assembly should tilt freely in either direction The will be fully tightened later when the alignment is performed Insert the flange of the bracket into the keyed hole of the wall or ceil mount bracket Slide the bracket forward into position The reflector now hang from the bracket Insert the correct screw and washer combination either wall or ceil mount through the slot and into the hole of the mounting bracket Tighten the screw until almost snug The assembly should still freely in both directions The screw will be fully tightened later the alignment is performed Adjust the reflector so that it is aiming directly at the transmitter receiver Once aimed correctly fully tighten both vertical and horizontal ad screws For proper operation of the beam detector the reflector must be se mounted to ensure no subsequent movement will occur after the instal is completed See Placement and Mounting sections of the detector manual for further details Test the system as indicated in the beam detector instructions 2 BEAMSMK WIRINg LOCATIONS 4 CEILINg MOUNTINg REFLECTOR for conduit Screw 21 4 Washer Washer Hub 5 8 NOT PAINT NOT PAINT Holes Bracket Adjustment 10 24 1 2 Washer Plastic Washer Metal Hex Nut Split lock Washer Bracket 3 WALL MOUNTINg TRANSMITTER RECEIvER UNIT Screw 13 8 Washer Washer Hole Hub NOT PAINT NOT PAINT Mounting Bracket Adjustment 10 24 1 2 Washer Plastic Washer Metal 5 8 Split lock Washer Bracket 2010 System Sensor

Related Files