Fire-Lite CDRM-300 Multiple Module with Two Relay Outputs and Two Monitor Inputs

File Preview
File Preview
Click below to download for free

Text Preview

INSTALLATION AND MAINTENANCE INSTRUCTIONS Multiple Module with Relay Outputs and Two Monitor Inputs FireLite Place CT 06472 203.484.7161 Operating Voltage Current Draw Operating Current Range Contact Rating Resistance IDC wiring resistance IDC Voltage IDC Current CONTACT RATINgS RATINg A A A A A A A A to 32 VDC mA 4 LEDs on mA 1 communication every 5 seconds to 120 0 to 49 to 93 Non condensing base address Relay Output 1 Module base address 1 Monitor Input 1 base address 2 Relay Output 2 Module base address 3 Monitor Input 2 H x 4.275 W x 1.4 D Mounts to a 4 square by 21 8 deep box Electrical Box EA CB Barrier at 30 VDC Ohms monitor iputs only Ohms Volts VOLTAgE DESCRIpTION VAC VDC VDC VDC VAC VDC VAC VAC 20ms 0.35 0.35 0.75 0.35 REqUIREMENTS ensure proper operation these modules shall be connected to listed com system control panels only All wiring must conform to applicable local codes ordinances and Install module wiring in accordance with the job drawings and appropri wiring diagrams the address on the module per job drawings Secure module to electrical box supplied by installer as shown in 2 1 CONTROLS AND INDICATORS INSTALLINg information is included as a quick reference installation guide Refer to control panel installation manual for detailed system information If the will be installed in an existing operational system inform the opera and local authority that the system will be temporarily out of service Dis power to the control panel before installing the modules This manual should be left with the owner user of this equipment DESCRIpTION CDRM 300 multi output input module is intended for use in intelligent systems where the individual address of each module is selected the built in rotary decade switches It is capable of replacing two indi relay control modules and two Class B monitor modules Each relay is intended for Form C switching applications which do not require supervision for the load circuit Each monitor input is intended to between a fire alarm control panel and one or more devices Each output has its own green LED Each monitored input has its own bi LED which can be controlled by the control panel module address is selected by means of rotary decade address switches Figure 1 These can be accessed from the front of the module A screw should be used to rotate the wheels to select the desired addresses module can use up to four 4 addresses The base address selected via rotary address switches will be assigned to relay output 1 from 00 to 156 module will automatically assign the next three addresses as appropriate monitored input 1 relay output 2 and monitored input 2 relay output 2 or monitored input 2 are not used please switch the cor DIP switch to the position with the screwdriver See Figure These two addresses will then be free to be used for other devices on loop NOTE If relay output 2 is disabled and monitored input 2 is the address for monitored input 2 will be module base address 3 base address 2 reserved for relay output 2 will then be open for devices 1A DISABLINg OUTpUT 2 AND INpUT 2 2 MODULE MOUNTINg module mounts directly to 4 inch square electrical boxes see Figure 2 box must have a minimum depth of 21 8 inches Surface mounted electri boxes SMB500 are available from System Sensor The module can also to the DNR W duct housing 3 TypICAL 2 WIRE INITIATINg CIRCUIT CONfIgURATION NfpA STyLE B NEXT NUMBER OF UL LISTED CONTACT DEVICES MAY BE USED THE IS PROGRAMMABLE E G IT WILL FOR ANY SIGNAL FOR WHICH THE IS PROGRAMMED DO NOT MIX FIRE DEVICES ON THE SAME MODULE INITIATING SUPERVISORY OR DEVICE CIRCUIT IDC NFPA STYLE B LIMITED 450 MAX 10.2 VDC MAX CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS TERMINALS ARE SUPERVISED AND POWER LIMITED ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE PANEL OR DEVICE MODULES TO LISTED COMPAT CONTROL PANELS ONLY LINE CIRCUIT SLC VDC MAX PAIR RECOMMENDED EOL EOL ANY WIRING TO TERMINALS 7 12 IS NONPOWER LIMITED EA CB BARRIER IS REQUIRED THE EA CB INCLUDES A LIMITED LABEL WHICH MUST BE PLACED OVER POWER LIMITED TERMINAL INFORMATION ON THE LABEL relay switch contacts are shipped in the standby open state but may have transferred to the activated closed state during shipping To ensure that the contacts are in their correct state modules must be made to communicate with the panel before connecting circuits controlled by the module FireLite Alarms

Related Files