Kidde 3101086-EN R006 FX-RLY Analog Contact Relay Module Installation Sheet

File Preview
File Preview
Click below to download for free

Text Preview

Analog Contact Relay Installation Sheet FX RLY Analog Contact Relay Module is an analog addressable that provides one Form C dry relay contact It can also be to provide polarity reversal of its output The module can be to control external appliances or shut down equipment device address is set using the two rotary switches located on the of the module One device address is required module is wired according to its operation as shown in The module is configured to operate as a relay nonsilence type from the factory It can function as either a control relay or reversal relay depending on how it is wired relay function Addressable device that provides one Form C relay contact The system firmware ensures that the relay is in the state when powered up Upon command from the control panel FX RLY relay energizes reversal relay function Addressable device that provides reversal of its output The system firmware ensures that the is in the proper state when powered up Upon command from the panel the FX RLY relay energizes reversing the polarity of its Additional device types are available through front panel or the configuration utility Refer to the applicable control technical reference manual operation module provides a bicolor LED that shows its status Green LED flashes Red LED flashes and wire this device in accordance with applicable national and codes ordinances and regulations Connecting a device that exceeds this module pilot duty ratings may cause activation failure This module does not capacitive loads See on page 2 for contact The module is shipped from the factory as an assembled unit it no user serviceable parts and should not be This module will not operate without electrical power As fires cause power interruption you should discuss further with your local fire protection specialist This module does not support conventional smoke detectors the module within the same room as the device it is install the module Verify that all field wiring is free of opens shorts and ground 2020 Carrier Wire the module in accordance with Figure 3 and 4 Set the module address Refer to the panel technical reference for a list of valid addresses a screwdriver to adjust the two rotary switches on the front of module Set the TENS rotary switch 0 through 12 for the 10s 100s digit and the ONES rotary switch for the 0 through 9 For example device address 21 set the TENS rotary switch 2 and set the ONES rotary switch to 1 see Figure 1 Mount the module on the electrical box using screws provided with electrical box see Figure 2 Mount the wall plate on the module using the hardware shown in 2 1 Module address Insert screwdriver here 2 Module installation Module Compatible electrical box Cover plate plastite screws 2X Wall plate Screw all wiring connections as shown in Figure 3 or Figure 4 to the desired function Be sure to observe the polarity of the Only one conductor per terminal The signaling line circuit SLC circuit is power limited and Refer to the panel documentation for SLC wiring specifications 2 3101086 EN REV 006 ISS 20OCT20 3 Control relay function Normally closed contact NC Normally open contact NO Common contact Class E Power limited unless connected to a nonpower limited If the source is nonpower limited eliminate the power mark and maintain a minimum of 0.25 in 6.4 mm space power limited wiring For other mounting methods see and bracket installation sheets to maintain separation power limited and nonpower limited wiring The wire size must capable of handling fault current from nonpower limited or 4 Polarity reversal relay function type FPL FPLR FPLP or permitted substitute cables these power limited cable conductors extending beyond jacket are separated by a minimum of 0.25 in 6.4 mm space by a nonconductive sleeve or nonconductive barrier from all conductors Refer to the NFPA 70 National Electrical Code more details Class A or Class B All wiring is power limited and supervised Signaling line circuit SLC from previous device Signaling line circuit SLC to next device Not used Normal Active Power out Power in Power limited unless connected to a nonpower limited source If source is nonpower limited eliminate the power limited mark maintain a minimum of 0.25 in 6.4 mm space from power wiring For other mounting methods see enclosure and installation sheets to maintain separation of power limited nonpower limited wiring The wire size must be capable of fault current from nonpower limited source or line voltage Maximum 20.6 V peak to peak VDC VAC ratings pilot duty type fault impedance A A resistive load 60 W or 62.5 VA C programmable k type FPL FPLR FPLP or permitted substitute cables these power limited cable conductors extending beyond jacket are separated by a minimum of 0.25 in 6.4 mm space by a nonconductive sleeve or nonconductive barrier from all conductors Refer to the NFPA 70 National Electrical Code more details All wiring is power limited and supervised Signaling line circuit SLC from previous device Signaling line circuit SLC to next device electrical boxes 4 in square 2 1 2 in 64 mm deep box in square 2 1 2 in 64 mm deep box 4 in square 1 1 2 in 38 mm box 14 16 or 18 AWG wire 2.5 1.5 or 0.75 mm2 Sizes 16 and 18 are preferred to 120 0 to 49 to 93 noncondensing at 32 size environment humidity temperature range to 140 to 60 information contact information see www kidde esfire com 2 3101086 EN REV 006 ISS 20OCT20

Related Files