Silent Knight SWIFT Instruction Manual for WSK-PHOTO

File Preview
File Preview
Click below to download for free

File Data

Name silent-knight-swift-instruction-manual-for-wsk-photo-9381206475.pdf
Type PDF
Size 922.01 KB
Downloads

Text Preview

I Clintonville Road Northford CT 06472 1610 203 484 7161 Fax 203 484 7118 AND MAINTENANCE INSTRUCTIONS WSK PHOTO T Intelligent Smoke Sensor Voltage Range Current Alarm Current LED on Transmit RF Power Frequency Range Humidity Range Temperature Range Type Life Replacement VDC 3.3 VDC one communication every 23.8 seconds with LED blink enabled mA 3.3 VDC LED on MHz to 93 Relative Humidity Non condensing to 120 0 to 49 32 to 100 0 to 38 Panasonic CR123A or 4 Duracell DL123A year minimum TROUBLE BATTERY LOW display and or during annual maintenance 61 mm installed in B501W Base 102 mm installed in B501W Base oz 230 g installed in B501W base with 4 batteries sensor must be installed in compliance with the control panel system manual and the SWIFT Wireless Manual The installation must the requirements of the Authority Having Jurisdiction AHJ Sensors maximum performance when installed in compliance with the National Protection Association NFPA see NFPA 72 DESCRIPTION WSK PHOTO and WSK PHOTO T are plug in type smoke sensors that a photoelectronic sensing chamber with wireless communication sensors transmit a digital representation of smoke density through a wire mesh to a gateway The gateway will send the information to the panel requested Rotary dial switches are provided for setting the sensor Figure 1 LEDs on the sensor are controlled by the panel to indicate sensor status WSK PHOTO T combines a photoelectronic sensing chamber and 135 fixed temperature heat detector Knight panels offer different features sets across different models As a certain features of the WSK PHOTO and WSK PHOTO T may be avail on some control panels but not on others The possible features available the WSK PHOTO and WSK PHOTO T if supported by the control panel are The panel controls the LED operation on the sensor Operational modes red green and amber colors in various solid or blink patterns refer to the operation manual for the UL listed control panel for specific of the WSK PHOTO and WSK PHOTO T WSK PHOTO and WSK PHOTO T require compatible addressable com to function properly Connect these sensors to listed compatible panels only Knight recommends spacing sensors in compliance with NFPA 72 In air flow applications with smooth ceilings space sensors 30 feet apart specific information regarding sensor spacing placement and special ap refer to NFPA 72 or the System Smoke Detector Application Guide from SystemSensor com technologies can exhibit communication disruption if devices are too close together To avoid this form of disruption SWIFT devices not be placed closer than 2 feet 60 cm apart without an intervening Do not attach the base and detectors to temporary structures such as ceiling tiles such that the placement could be altered To prevent in device placement permanently secure the structure or mount the across the ceiling panel support as shown in Figure 2 REPLACEMENT battery levels on the wireless devices are displayed as a trouble on the Therefore when the message BATTERY LOW is displayed the battery in the device This message is an indication that approxi one week of battery life remains replace the batteries in a wireless device use the following steps Have 4 CR123A or DL123A batteries available Remove the detector from the base Open the battery compartment refer to Figure 3 Note The battery compart cover may be left attached at the hinges during battery replacement Remove the used batteries and replace with new batteries The battery is designed such that the batteries can only align in the ap direction Do not force the batteries into the openings Replace the battery compartment cover Return the device to its original location 1 ROTARY ADDRESS SWITCHES 0 0 2 CEILING PANEL SUPPORT 3 BATTERY COMPARTMENT covers provide limited protection against airborne dust particles during Dust covers must be removed before the sensors can sense smoke sensors prior to heavy remodeling or construction RESISTANCE and WSK PHOTO T include a tamper resistant capability that their removal from the base without the use of a tool Refer to the manual for details on making use of this capability The base also in a magnet for tamper resistance The magnet activates a supervisory fault at the panel if the detector is removed from the base testing notify the proper authorities that the system is undergoing and will temporarily be out of service Disable the system to unwanted alarms sensors must be tested after installation and periodically thereafter Testing must satisfy the Authority Having Jurisdiction AHJ Sensors offer max performance when tested and maintained in compliance with NFPA 72 sensor can be tested in the following ways Functional Magnet Test P N M02 04 01 or M02 09 00 This sensor can be functionally tested with a test magnet The test mag electronically simulates smoke in the sensing chamber as well as the sensor electronics and connections to the control panel Hold the test magnet in the magnet test area as shown in Figure 4 The sensor should alarm the panel Two LEDs on the sensor are controlled by the panel to indicate sensor Coded signals transmitted from the panel can cause the LEDs blink latch on or latch off Refer to the control panel technical docu for sensor LED status operation and expected delay to alarm Smoke Entry The GEMINI model 501 aerosol generator can be used for smoke entry Set the generator to represent 4 ft to 5 ft obscuration as de in the GEMINI 501 manual Using the bowl shaped applicator aerosol until the panel alarms Additionally canned aerosol simulated smoke canned smoke agent be used for smoke entry testing of the smoke detector Tested and aerosol smoke products are Safeguard Industries and 30S and CHEK06 used properly the canned smoke agent will cause the smoke detector go into alarm Refer to the manufacturer published instructions for proper of the canned smoke agent aerosol simulated smoke canned smoke agent formulas will vary by Misuse or overuse of these products may have long term ad effects on the smoke detector Consult the canned smoke agent manufac published instructions for any further warnings or caution statements Direct Heat Method Hair dryer of 1000 1500 watts A hair dryer of 1000 1500 watts should be used to test the thermistors Di the heat toward either of the two thermistors holding the heat source 12 inches from the detector in order to avoid damaging plastic housing The detector will reset only after it has had sufficient to cool Make sure both thermistors are tested individually sensor that fails any of these tests should be cleaned as described under and retested If the sensor fails after cleaning it must be replaced returned for repair testing is complete restore the system to normal operation and notify proper authorities that the system is back in operation removing the detector notify the proper authorities that the smoke de system is undergoing maintenance and will be temporarily out of service the zone or system undergoing maintenance to prevent unwanted alarms Remove the sensor to be cleaned from the system Remove the sensor cover by pressing firmly on each of the four removal that hold the cover in place refer to Figure 5 Vacuum the screen carefully without removing it If further cleaning is continue with Step 4 otherwise skip to Step 7 Remove the chamber cover screen assembly by pulling it straight out Use a vacuum cleaner or compressed air to remove dust and debris from sensing chamber Reinstall the chamber cover screen assembly by sliding the edge over the chamber Turn until it is firmly in place Replace the cover using the LEDs to align the cover and then gently it until it locks into place Make sure that t

Related Files