Simplex 4009-9807 NAC Option Card Installation Instructions

File Preview
File Preview
Click below to download for free

Text Preview

Cautions and Warnings NAC Option Card Instructions NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS Upon unpacking your Simplex product inspect the contents of the for shipping damage If damage is apparent immediately file a claim the carrier and notify Simplex HAZARD Disconnect electrical power when making any adjustments or repairs Servicing should be performed by qualified Representatives HAZARD Static electricity can damage components Therefore as follows Ground yourself before opening or installing components use the 553 484 Control Kit Keep uninstalled component wrapped in anti static material at all times FREQUENCY ENERGY This equipment generates uses and can radio frequency energy and if not installed and used in accordance with instruction manual may cause interference to radio communications It has tested and found to comply with the limits for a Class A computing device to Subpart J of Part 15 of FCC Rules which are designed to provide protection against such interference when operated in a commercial Operation of this equipment in a residential area may cause in which case the user at his own expense will be required to take measures may be required to correct the interference publication shows how to install the 4009 9807 NAC Option Card Part No into a 4009 IDNet cid 1 NAC Extender 4009 IDNet The NAC option provides the 4009 IDNet Extender with four additional NAC circuits to the 4009 IDNet cid 1 NAC Installation Instructions 574 181 for information Refer to the 842 068 Field Wiring Diagram for wiring information this Publication publication discusses the following topics Page Option Card Installation 1999 Simplex Time Recorder Co Gardner MA 01441 0001 USA specifications and other information shown were current as of publication and are subject to change without notice is a trademark of Simplex Time Recorder Company A Option Card FIELD WIRING TB2 BOARD addition to the four NACs found on the 4009 System Board an aftermarket option card is available to provide four additional Class B Style Y NACs To support Class A Style Z you must install a Class A option card that mounts onto the NAC option card Refer to the 4009 Class A Adapter Option Card Installation Instructions 574 326 Each NAC option card supports up to two Class A option card s 1 illustrates the location of the NAC option card plug connector interfaces the two terminal blocks that support the additional four NACs A ADAPTER P2 POWER INPUT SYSTEM BOARD NAC has a yellow LED to indicate a trouble condition or the state of that NAC The condition state for the NACs are as IN ALARM NAC 1 4 LED IN SUPERVISORY LED OK SLOW FLASH SHORT FAST FLASH OPEN CIRCUIT TROUBLE 1 4 NOTE 1 4009 9807 NAC Option Card the information in Figure 2 to terminate all Class B and Class A wiring to the 842 068 Field Wiring Diagram for complete wiring compatible current and line distance information Maximum current for each is 1.5 Amps All wiring to be 18AWG minimum to local code and Power Limited B Wiring B Style Y wiring on the option card four NAC circuits are connected to terminal strips TB1 TB2 at the top edge of the NAC option card The circuits NAC5 NAC8 are supervised with a 10K End of Line EOL Install a 10K cid 1 1 2W Part No 378 030 Brown Black Orange EOL from to terminals of the NAC Option Card on each unused A Wiring A Style Z NAC operation is achieved by installing the 4009 9808 Class Adapter Option Card The Class A wiring is terminated at terminal strips TB2 at the top edge of the NAC option card Install a 10K cid 1 1 2W Part 378 030 Brown Black Orange EOL resistor from to terminals of Class A NAC in use on the Class A module Set the Hardware Switch SW1 for Class A operation SW1 Position 3 to for Class A Adapter NAC 5 and 6 present SW1 Position 4 to for Class A Adapter NAC 7 and 8 present Option Card Wiring a 10K cid 1 1 2W Part No 378 030 EOL resistor from to terminals TB1 of each Class A in use on the Class A module a 10K cid 1 1 2W Part No 378 030 EOL resistor from to terminals TB1 and or TB2 of Board on each unused circuit All wiring to be 18AWG minimum or to code All wiring is supervised and Power Limited HARNESS 2 NAC Option Card Wiring Installation the NAC Option a 4009 9807 NAC Option Card onto the 4009 IDNet option card plate 636 871 using the following steps and Figure 3 Disconnect battery and then AC power from the 4009 IDNet Secure the option card plate assembly 636 871 to the 4009 IDNet using slotted torx screws supplied the dual row 26 pin header 166 492 into system board connector Line up the back 26 pin connector P4 of the NAC option card with the 26 header installed on the 4009 system board and insert pins into Secure the NAC option card to the plate assembly using four slotted torx supplied the two position signal power harness 733 972 from system board P7 to NAC option card connector P3 Set the hardware configuration switch SW1 position 7 located on the board to to configure the NAC option card Refer to the IDNet NAC Extender Installation Instructions 574 181 for detailed on setting the hardware configuration switch SW1 can now reconnect AC and Battery Power SWITCH HEADER 166 492 SHOWN TORX SCREW LONG 4 A ADAPTER 565 789 CARD ASSEMBLY TORX SCREW LONG 4 A 3 NAC Option Card Installation

Related Files