Simplex 4009-9809 IDNet Repeater Option Card Installation Instructions

File Preview
File Preview
Click below to download for free

Text Preview

Cautions and Warnings IDNet Repeater Option Card Instructions NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS Upon unpacking your Simplex product inspect the contents of the for shipping damage If damage is apparent immediately file a claim the carrier and notify Simplex HAZARD Disconnect electrical power when making any adjustments or repairs Servicing should be performed by qualified Representatives HAZARD Static electricity can damage components Therefore as follows Ground yourself before opening or installing components use the 553 484 Control Kit Keep uninstalled component wrapped in anti static material at all times FREQUENCY ENERGY This equipment generates uses and can radio frequency energy and if not installed and used in accordance with instruction manual may cause interference to radio communications It has tested and found to comply with the limits for a Class A computing device to Subpart J of Part 15 of FCC Rules which are designed to provide protection against such interference when operated in a commercial Operation of this equipment in a residential area may cause in which case the user at his own expense will be required to take measures may be required to correct the interference publication shows how to install the 4009 9809 IDNet Repeater Option Card No 565 773 into a 4009 IDNet NAC Extender 4009 IDNet or 4009 Addressable Controller 4009 TrueAlert The repeater card and provides a power and distance boost for the IDNet channel and it on its output side at host panel IDNet levels to the 4009 IDNet NAC Extender Installation Instructions 574 181 or Addressable Controller Installation Instructions 574 762 for information Refer to the 4009 IDNet Field Wiring Diagrams No 842 068 or 4009 TrueAlert Addressable Controller Field Wiring Part No 842 158 for additional wiring information Page Repeater Option Card Installation this Publication publication discusses the following topics 2000 Simplex Time Recorder Co Westminster MA 01441 0001 USA specifications and other information shown were current as of publication and are subject to change without notice and TrueAlert are trademarks of Simplex Time Recorder Company B Repeater Option Card 1 illustrates the IDNet Repeater Option Card interface and the terminal that supports the IDNet interface INTERFACE BOARD 1 4009 9809 IDNet Repeater Option Card Card Wiring the information in Figure 2 to terminate all Class A Style 6 wiring For B Style 4 wiring connect a jumper wire s from TB1 1 to TB1 3 and TB1 2 to TB1 4 Refer to the 4009 IDNet Field Wiring Diagrams Part No or 4009 TrueAlert Addressable Controller Field Wiring Diagrams No 842 158 for complete wiring compatible appliances current and line information IDNet System Board Assembly 565 771 System Board 565 771 or System Board 565 990 TrueAlert Main Board Assembly 565 990 Repeater Card A A B B Side of IDNet Channel Side of IDNet Channel Note 1 Refer to the 4009 IDNet Field Wiring Diagrams Part No 842 068 or TrueAlert Addressable Controller Field Diagrams Part No 842 158 for Class B and Class A connections Maximum number of devices on repeated portion of IDNet channel is 100 Total devices on host IDNet channel repeated IDNet channel s combined not to exceed 250 2 IDNet Repeater Option Card Wiring Installation the Repeater Card the 4009 9809 Repeater Option Card onto the 4009 IDNet or 4009 TrueAlert card plate assembly 636 871 using the following steps and Figure 3 Disconnect battery and then AC power from the 4009 IDNet or 4009 TrueAlert Secure the option card plate assembly 636 871 to the 4009 IDNet or 4009 using four slotted torx screws supplied the 14 pin header Part No 166 490 into 4009 IDNet System Board P6 or 4009 TrueAlert Main Board connector P4 Line up the back 14 pin connector P1 of the IDNet Repeater Option Card with the header installed on the 4009 IDNet System or 4009 TrueAlert Main Board insert pins into connector Secure the IDNet Repeater Option Card to the plate assembly using four slotted torx supplied For the 4009 IDNet set the hardware configuration switches SW1 position 5 located the 4009 IDNet System Board to to configure the IDNet Repeater Option to the 4009 IDNet and SW1 position 8 to for IDNet control Refer to 4009 IDNet NAC Extender Installation Instructions 574 181 for detailed on setting the hardware configuration switch SW1 the 4009 TrueAlert set the hardware configuration switches SW4 position 3 and on the 4009 TrueAlert Main Board to and respectively for IDNet and SW4 position 5 to to configure the IDNet Repeater Option Card to 4009 TrueAlert Refer to the 4009 TrueAlert Addressable Controller Installation 574 762 for detailed information on setting the hardware configuration SW4 can now reconnect AC and Battery Power OF 4009 IDNet NAC HARDWARE CONFIGURATION SW1 OF 4009 TrueAlert CONTROLLER HARDWARE SWITCH SW4 CARD ASSEMBLY TORX SCREW LONG 4 IDNet System Board Assembly 565 771 System Board 565 771 or TrueAlert Main Board Assembly 565 990 System Board 565 990 Repeater Card TORX SCREW LONG 4 HEADER 166 490 SHOWN 3 IDNet Repeater Option Card Installation P1 B

Related Files