Simplex 4100 4120-0154, 4100-6048 VESDA Interface Card - Installation Instructions

File Preview
File Preview
Click below to download for free

Text Preview

Introduction Contents Shipment 4100 6048 Interface Card Instructions publication describes the installation procedure for the 4100 4120 0154 and 4100 6048 Interface modules document covers the following topics Configuring wiring and installing a VESDA RS 232 Interface card in a 4100 4100U FACP Adding supervisory wiring to a VESDA power supply This wiring is only required for power supplies and is not required if VESDA detectors are powered by 4100 power attempting to install the VESDA RS 232 interface card make sure that the 4100 FACP not already have 10 MAPNET style cards installed in it A 4100 FACP limits the number of card slots to 10 AC power and disconnect the battery from the system when installing and wiring the RS 232 interface card unpacking your Simplex product inspect the contents of the carton for shipping damage If is apparent immediately file a claim with the carrier and notify Simplex Guide for Detectors This document ships with the VESDA LaserPLUS It describes the installation and wiring of VESDA LaserPLUS detectors and instructions for connecting the detector network to the VESDA High Level Interface board Field Wiring Diagrams 841 731 power limited or 841 995 non power limited Field Wiring Diagram 841 804 Fire Alarm System Installation Guide 574 848 this Publication publication discusses the following topics Page and Warnings Jumpers Switches the Motherboard into 2975 91xx Back Boxes 4100 Motherboards into 2975 94xx Back Boxes 4100U the Daughter Card a Power Supervision Circuit for VESDA Power Supplies 2001 Simplex Time Recorder Co Westminster MA 01441 0001 USA specifications and other information shown were current as of publication and are subject to change without notice is a registered trademark of Vision Systems A and Warnings AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation These instructions must be followed to avoid damage to this product and associated Product operation and reliability depends upon proper installation HAZARD Disconnect electrical field power when making any internal or repairs Servicing should be performed by qualified Simplex Representatives HAZARD Static electricity can damage components Therefore handle as follows Ground yourself before opening or installing components use the 553 484 Static Control Prior to installation keep components wrapped in anti static material at all times FREQUENCY ENERGY This equipment generates uses and can radiate radio energy and if not installed and used in accordance with the instruction manual may interference to radio communications It has been tested and found to comply with the for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules which are to provide reasonable protection against such interference when operated in a environment Operation of this equipment in a residential area may cause interference which case the user at his own expense will be required to take whatever measures may be to correct the interference Jumpers Jumper jumpers on the VESDA RS 232 interface daughter card are factory preset and should not modification If necessary use this section to verify that the jumpers are in the correct See Table 1 and Figure 1 1 VESDA Default Jumper Settings the table above 2 3 means you should place the jumper on pins 2 and 3 whereas a designation 1 2 means you should place the jumper on pins 1 and 2 s s 1 Jumper Settings for VESDA RS 232 Interface Card Switches SW1 on the VESDA RS 232 interface daughter card is a bank of eight dip switches From to right see figure below these switches are designated as SW1 1 through SW1 8 The of these switches is as follows SW1 1 This switch sets the baud rate for the serial communication line running between the RS 232 interface card and the 4100 CPU Set this switch to ON SW1 2 through SW1 8 These switches set the card address within the 4100 FACP switches must be set to the value assigned to the card by the 4100 Programmer Refer Table 1 for a complete list of the switch settings for all of the possible card addresses a switch to the down position to turn it ON or to the up position to turn it OFF Switches 1 2 through 1 8 the Card Address Figure an Address of 3 Refer Table 1 for switch settings Rate SW 1 1 Be Set to 2 Jumper Settings for the VESDA RS 232 Interface Card on next page Switches Continued continued 2 4100 Daughter Card Addresses 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 2 1 3 1 4 1 5 1 6 1 7 1 8

Related Files