Solidyne sLON-2x, 3x, 4x Data Sheet

File Preview
File Preview
Click below to download for free

File Data

Name solidyne-slon-2x-3x-4x-data-sheet-4607193528.pdf
Type PDF
Size 828.02 KB
Downloads

Text Preview

TECH DATA SHEET Controller sLON 2xx sLON 3xx and sLON 4xx sLON 2 and sLON 4 Controllers are interoperable designed in accordance with LONMARK and equipped with LONMARK HVAC profiles controllers support sLON WTSx digital sensors indicators a wiring subbase with removable field wiring terminal blocks as well as DIN or panel mounting ability are other features of these They function in standalone mode or as of a LONWORKS Network using the integral FT Free Topology communications transceiver A connection to a sLON ADPx Communication and a PC with WPT Software Tool software is to download and modify applications Chart Controller with Coil Profile 8020 Controller with Pump Profile Controller with Profile 8030 Controller with Profile 8030 Controller with Coil Profile 8020 Controller with Pump Profile Controller with Profile 8030 Controller with Profile 8030 Controller with Coil Profile 8020 Controller with Pump Profile Controller with Profile 8030 Controller with Profile 8030 Digital Input DI Universal Inputs UI Digital Outputs DO Universal Inputs UI Digital Outputs DO Analog Outputs AO Digital Inputs DI Universal Inputs UI Digital Outputs DO Analog Outputs AO Corporation www solidyne com sLON 3xx sLON 4xx rev1 03 2005 items not provided carton for damage If damaged notify carrier immediately Inspect controllers for upon receipt must be a qualified experienced technician Job wiring diagrams Tools Drill and bits for panel mounting screws Digital Volt ohm meter DVM Static protection wrist strap Class 2 power transformer supplying a nominal 24 Vac 20.4 to 30 Vac with a minimum of 15 Va 50 60 Hz per controller plus Digital Output DO loads if same is used In European Community transformer must conform to EN 60742 Terminators One sLON T1 terminator required for each free topology segment Two sLON T2 terminators required for each bus topology segment Two 6 pan head panel mounting screws or 35mm DIN rail for mounting sLON 3xx sLON 4xx rev1 03 2005 Electrical shock hazard Disconnect power before installing or removing the Follow Static precautions when installing this equipment Use copper conductors that are suitable for 167 75 Make all connections according to electrical wiring diagram national and local electrical Precautions charges damage electronic components The microprocessor and associated circuitry extremely sensitive to static discharge Use the following precautions when installing or operating the system Work in a static free area Discharge static electricity by touching a known securely grounded object Use a wrist strap connected to earth ground when handling the controller printed board Communications Commission FCC equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules These limits are designed to provide protection against harmful interference in residential installations This generates uses and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions Even when are followed there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception can be determined by turning the equipment off and on user is encouraged to to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Connect the equipment to an outlet on a circuit different from that to which the receiver the separation between the equipment and receiver connected Consult the dealer or an experienced radio television technician for help Department of Communications DOC class B digital apparatus meets all requirements of the Canadian Interference Causing Regulations Community Directives equipment meets all requirements of European Community Directives for Low Voltage General Safety 92 59 EEC and Electromagnetic Compatibility Avoid locations where excessive moisture corrosive fumes vibration or explosive are present Avoid electrical noise interference Do not install near large contactors electrical or welding equipment Locate where ambient temperatures do not exceed 140 60 or fall below 40 and relative humidity does not exceed 95 or fall below 5 non condensing controllers are suitable for indoor use only sLON 3xx sLON 4xx rev1 03 2005 or DIN Rail Mounting Select mounting location Enclosure mounting is recommended Do one of the following Using two 6 pan head screws mount base of controller to a panel Figure 1 Snap controller base on a 35mm DIN mounting rail not provided Multiple units can mounted side by side on a DIN mounting rail Wire controller base See Wiring section After wiring insert cover tabs into brackets on base of the controller and gently push cover snaps into place View 51 shown are in inches mm Mounting Dimensions sLON 3xx sLON 4xx rev1 03 2005 Figures 2 3 and 4 when making electrical connections to controller following electrical connections can be made to the controllers Sensor Link S Link connection to sLON WTS sLON WTSx LONWORKS network LON connection connections including Universal Inputs Digital Inputs sLON 2 and sLON 4 Analog sLON 3 and sLON 4 and Digital Outputs Power connection to a 24 Vac nominal Class 2 power source and earth ground Inputs to 5 Vdc to 20mA Thermistor Balco Platinum Input Contact Link sLON WTSx Network 3150 Transceiver Service Pin Button Network Jack Power Vac 50 60 Hz 2 EN 60742 VA per Controller DO load if transformer is Outputs Vac Class 2 24 Vdc or less VA per output Duty A SPST Open NO detect a closed switch maximum resistance must be less than 300 ohms detect an open switch minimum resistance must be greater than 1.5K ohms which use 0 to 20 mA analog inputs require a 250 ohm shunt resistor kit AD 8969 202 resistor across universal input and common detect an open switch minimum resistance must be greater than 100K ohms Input signals of 1 to 11 Vdc must be converted to 0.45 to 5 Vdc with a voltage divider AD 8961 220 which use a 10K Thermistor Sensor universal input require an 11K ohm shunt resistor AD 8969 206 Install resistor across universal input and common sLON 2 Terminal Connections sLON 3xx sLON 4xx rev1 03 2005 Inputs to 5 Vdc to 20mA Thermistor Balco Platinum Outputs to 20mA into an to 550 load Link sLON WTSx Network 3150 Transceiver Service Pin Button Network Jack Power Vac 50 60 Hz 2 EN 60742 VA per Controller DO load if transformer is Outputs Vac Class 2 24 Vdc or less VA per output Duty A SPST Open NO detect a closed switch maximum resistance must be less than 300 ohms detect an open switch minimum resistance must be g

Related Files