System Sensor B114LPBT Manual

File Preview
File Preview
Click below to download for free

File Data

Name system-sensor-b114lpbt-manual-5198230764.pdf
Type PDF
Size 1.25 MB
Downloads

Text Preview

I AND MAINTENANCE INSTRUCTIONS Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 Plug in Detector Base use with the following smoke detectors US 1151 2151 2151T 1151A 2151A 2151TA EUROPE 1151E 2151E Diameter Height Temperature Range Humidity Range Ratings includes base and detector Voltage Contact Ratings Resistive Load Form A 2.0A 30VAC DC Form C 2.0A 30VAC DC 1.0A 125VAC Current Current Time after 60 second reset 36.0 Seconds maximum in 15.7 cm in 2.9cm lb 260 g square box without plaster ring minimum depth 1.5 4 octagon box minimum depth 1.5 octagon box minimum depth 1.5 to 49 32 to 120 to 93 Relative Humidity used the RA400 Remote Annunciator and RTC operates within the specified detector system voltage mA typical 24V AC DC 35 mA maximum 35V AC DC mA typical 24V AC DC 94 mA maximum 35V AC DC VAC DC 60 Hz INSTALLING read thoroughly System Sensor Applications Guide for System Smoke SPAG91 which provides detailed information on detector spacing zoning wiring and special applications This is available online System Sensor web site www systemsensor com This manual should be left with the owner user of this equipment The detector used with this base must be tested and maintained following NFPA 72 requirements The detector used with this base be cleaned at least once a year DESCRIPTION B114LPBT detector base is designed for use with System Sensor model photoelectronic and 1151 ionization detector heads The capability of these detectors into a variety of special bases makes them more ver than equivalent direct wired models Refer to the System Sensor catalog other available plug in bases The B114LPBT base is intended for use in systems with terminals provided for remote annunciator and relay con detector base mounts directly to 31 2 and 4 inch octagon boxes and square boxes To mount the base remove the decorative ring by rotat it in either direction to unhook the snaps before separating the ring from base Use the screws supplied with the junction box to attach the base to box through the appropriate mounting slots in the base the decorative ring around the base and rotate it in either direction the ring snaps into place see Figure 2 TERMINALS Annunciator Coil Used Annunciator Relay A Contacts Relay A Relay C Contacts GUIDELINES wiring must be installed in compliance with the National Electrical Code applicable local codes and any special requirements of the authority hav jurisdiction using the proper wire size The conductors used to connect detectors to control panels and accessory devices should be color to reduce the likelihood of wiring errors Improper connections can a system from responding properly in the event of a fire signal wiring the wiring between interconnected detectors it is recom that the wire be no smaller than 16 gauge 1.5 square mm and that or three conductor wire be no smaller than 18 gauge 1.0 square mm best performance alarm loop conductors should be installed in separate conduit or shielded cable to protect the alarm loop from extraneous interference detectors and alarm systems control panels have specifications for al loop resistance Consult the control panel manufacturer specifica for the total loop resistance allowed for the particular model control being used before wiring the detector loops 1 BASE TERMINALS GAUGE 14 2 MOUNTING BASE TO BOX SUPPLIED TAB ON SUPPLIED 11 9 3 TYPICAL WIRING DIAGRAM FOR 24VAC RMS DC DETECTOR SYSTEMS INITIATION LOOP ABOVE DIAGRAM SHOWS NFPA REQUIRED WIRING OF SUPERVISED SYSTEMS SHOWN BELOW FOR REFERENCE BY PANEL 11 9 INSTRUCTIONS Refer to the manufacturer instructions for releasing device wiring To ensure that electrical connections are supervised do NOT loop under terminals 8 9 10 and 11 Cut the wire at each terminal make electrical connections strip approximately 3 8 inch 1 cm insulation the end of each wire slide the bare wire end under the clamping plate tighten the clamping plate screw Use the strip gauges molded into the and underside of the base for ease of wiring to terminals 1 and 4 and terminals 6 through 14 respectively zone wiring of the detector base should be checked before installing the detector heads The base contains a built in shorting spring to make possible After the detector base is wired and mounted to an electrical position the shorting spring against terminal 3 This temporary connec energizes the supervisory relay and permits the wiring of the loop to be for continuity all detector bases have been mounted wired and the wiring checked the detector heads The shorting spring in the base automatically disen when the detector head is removed from the base DO NOT remove the spring since it reengages as the detector head is turned into the base the circuit FEATURE detector base also includes an optional tamper resistant feature that activated prevents removal of the detector without the use of a tool LEVER TAB AT DOTTED LINE BY TOWARD CENTER OF BASE make the base tamper resistant simply break off the tab on the base see 4A before installing the detector remove the detector from the base after it has been made tamper resistant a small screwdriver see Figure 4B into the small hole and press the lever away from the detector Rotate the detector counterclockwise and Head removal after activating the tamper resistance feature first re removal of the decorative ring 4A ACTIVATING TAMPER RESISTANCE FEATURE LEVER TAB AT DOTTED LINE BY TOWARD CENTER OF BASE 4B REMOVING DETECTOR HEAD FROM BASE SMALL BLADED SCREWDRIVER TO PUSH LEVER IN DIRECTION OF ARROW LIMITED WARRANTY Sensor warrants its enclosed smoke detector base to be free from defects in mate and workmanship under normal use and service for a period of three years from date manufacture System Sensor makes no other express warranty for this smoke detector No agent representative dealer or employee of the Company has the authority to or alter the obligations or limitations of this Warranty The Company obligation this Warranty shall be limited to the repair or replacement of any part of the smoke base which is found to be defective in materials or workmanship under normal and service during the three year period commencing with the date of manufacture phoning System Sensor toll free number 800 SENSOR2 736 7672 for a Return number send defective units postage prepaid to Honeywell 12220 Rojas Suite 700 El Paso TX 79936 USA Please include a note describing the malfunc and suspected cause of failure The Company shall not be obligated to repair or units which are found to be defective because of damage unreasonable use or alterations occurring after the date of manufacture In no case shall the be liable for any consequential or incidental damages for breach of this or any Warranty expressed or implied whatsoever even if the loss or damage is caused by Company negligence or fault Some states do not allow the exclusion or limitation of or consequential damages so the above limitation or exclusion may not apply you This Warranty gives you specific legal rights and you may also

Related Files