System Sensor spectralert-sp2- instal and maint

File Preview
File Preview
Click below to download for free

File Data

Name system-sensor-spectralert-sp2-instal-and-maint-1937568240.pdf
Type PDF
Size 891.86 KB
Downloads

Text Preview

INSTALLATION AND MAINTENANCE INSTRUCTIONS SP2 Series Speaker Strobes for Protective Signaling Systems use with the following models SP2R2415 SP2R2430 SP2R241575 SP2R2475 SP2R24110 SP2W2430 SP2W241575 SP2W2475 SP2W24110 SENSOR Division of Pittway 3825 Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 to 18 AWG 3.31 to 0.82 mm2 inches 101 mm Speaker Terminals Size Dimensions 8.25 x 4.9 Input Range Range 32 cid 176 to 120 cid 176 F 0 cid 176 to 49 cid 176 C volts or 70.7 volts nominal 4000 Hz 1 2 1 and 2 Watts This manual shall be left with the owner user of equipment Description National Fire Protection Association NFPA has pub standards and recommended practices for the described in this manual As a result the must be familiar with these requirements as well all local codes and special requirements of the authority jurisdiction SpectrAlert SP2 series speakers can be operated with amplifiers having an output voltage of either volts or 70.7 volts speakers operate at any one of four input power levels output sound level is selected at the time of installa but can be changed if necessary speaker is also equipped with a capacitive input to al for DC supervision SpectrAlert SP2 series strobe can be installed in using 24 volt panels having DC or full wave FWR power supplies The strobes can also be in applications requiring synchronization MDL or no module required do not SpectrAlert SP2 series speaker strobes are designed to the requirements of most agencies governing these including NFPA ADA The National Fire Alarm UL CSFM MEA Also check with your local Au Having Jurisdiction for other codes or standards may apply Supply Considerations For Strobes typically supply DC filtered voltage or FWR full Strobe Range DC or Full Wave Rectified to 30 volts 21 to 30 with MDL module flash per second Rate Output Models with 1575 are listed at 15 candela UL1971 but will provide 75 candela axis straight ahead with 15 30 75 or 110 are rated for candela rectified voltage The system design engineer must the number of units used in a zone based on the of panel supply Be certain the sum of all the device do not exceed the current capability of the panel are based on using the device current found Table 2 and must be the current specified for the type of power supply used Sizes designer must be sure that the last device on the circuit sufficient voltage to operate the device within its rated When calculating the voltage available to the last it is necessary to consider the voltage drop due to resistance of the wire The thicker the wire the less the drop Generally for purposes of determining the size necessary for the system it is best to consider all the devices as on the end of the supply circuit case wire size resistance AWG solid Approximately 8 ohms 1,000 ft AWG solid Approximately 5 ohms 1,000 ft AWG solid Approximately 3 ohms 1,000 ft AWG solid Approximately 2 ohms 1,000 ft Assume you have 10 devices on a zone and each 50 mA average and 2000 Ft of 14 AWG wiring to length outgoing return The voltage at the end of loop is 0.050 amps per device x 10 devices x 3 ohms ft x 2000 ft 3 volts drop same number of devices using 12 AWG wire will pro only 2 volts drop The same devices using 18 AWG will produce 8 volts drop Consult your panel specifications as well as SpectrAlert oper voltage range to determine acceptable voltage drop Manuals Online wiring must be installed in compliance with the Na Electrical Code NEC and applicable local codes as as special requirements of the authority having juris using the proper wire size This also includes all NFPA Standards ANSI UL 1480 UL 1971 and 760 Connect the speaker strobe as shown in Figure 1 Keep mind that even though the speaker and strobe are a mechanical unit they are electrically independent require separate power sources Do NOT loop electrical wiring under terminal Wires connecting the device to the control must be broken at the device terminal con in order to maintain electrical supervision 1 Electrical connections 2 Voltage and Power Selection ol lo ol ls2J 1 Sound levels for each transformer power tap 10 ft W W W W W 1 4 W 75 W 1 4 W 78 NEXT OR EOL 10 ft FROM FROM SUPPLY NEXT OR EOL Supply power for strobe must be continuous for operation See Figure 2 as an example of how to select a 1 4 Watt when a 25 volt amplifier is being used Notice that header SW1 has two shunts One shunt is used to either 25 or 70.7 volts input The other shunt is to select input power of 1 4 1 2 1 or 2 Watts 1 lists the UL reverberant and anechoic output levels for each power tap on the SP2 series 2 Current draw of strobes levels exceeding 130 rated signal voltage can the speaker Consequently an incorrect tap may cause speaker damage This means that a 25V tap is selected when a 70.7V amplifier is being speaker damage may result Therefore be sure to the proper taps for the amplifier voltage input level combination being used CURRENT mA CURRENT mA RUSH CURRENT mA Models Models Models FWR DC FWR DC FWR FWR DC FWR DC FWR 204 135 208 135 185 56 65 49 64 44 62 150 199 150 207 150 198 201 183 219 183 216 78 440 340 460 330 480 145 170 123 159 102 141 560 450 570 420 620 220 140 191 115 174 67 82 58 FWR DC FWR DC FWR 97 129 116 152 147 198 135 116 164 147 211 97 129 116 152 147 198 240 230 280 290 380 230 220 290 290 370 Manuals Online strobe module 3 Reversible strobe module Screw the back box be located near an obstruction such as doorway the strobe module is field reversible Fig 3 reverse the strobe module loosen the strobe screw the strobe module and lift it away from the mounting Turn the module so that it is upside down from its position and re insert the module into the mount plate be sure to insert Locking Rib into slot tighten screw Turn the entire assembly so that the word is right side up The unit can now be mounted mount back box speaker strobe can be flush mounted on a 4 x 4 x 2 back box Fig 4 as follows Select the appropriate pair of diagonally opposite holes in the speaker grille that will be used to the speaker strobe to the back box Do not insert mounting screws at this point Plug the two holes that will not be used for attachment two 8 32 x 1 3 4 pan head screws and hex nuts Use the two remaining 8 32 x 1 3 4 pan head screws to the speaker to the back box Two drywall screws provided may be used to fas the mounting plate to the wall To use the dry screws it will be necessary to first loosen the screw and hinge the strobe module away the mounting plate mount with SP2 BBS back box skirt optional back box skirt is available to provide a finished Mount the skirt to the back box using the screws provided with the skirt as follows Select the appropriate pair of diagonally opposite holes in the speaker grille that will be used to the speaker strobe to the back box Do not insert mounting screws at this point Plug the two holes that will not be used for attachment two 8 32 x 1 3 4 pan h

Related Files