Category: Solidyne

No text preview available.

i3 3220 Installation Instructions 3 05/27/2004 Comm. Bus: the IZAC communication bus to COM2. Use the terminal block to wire only the B+ and B- wires the i3. Wire the B+ wire to the left terminal and the to the right terminal. i3 is shipped with a 5vdc power supply that must be for proper operation. Figure 1 shows the +5V where the power supply plug should be ethernet port on the i3 is used for TCP/IP The RJ-45 connector labeled ETH is the Ethernet port which supports all 10/100 Mbps connections. Tunneling Feature: i3 serial tunneling feature is used in conjunction Solidyne ICMS Windows based programming It allows the ICMS software to connect to IZAC network through the i3. This is done by using M204AN plugged into the serial port COM1 of Figure This tunneling feature used TCP port 7001 along with party software programs for serial-to-IP conversion. more information about this serial tunneling feature, 1 Communication Addressing: i3 ships from the factory with the default IP of 10.0.0.1 easiest method of changing this address is to use built-in configuration web pages of the i3. To these pages you must plug the i3 ethernet cable a hub/switch or directly to a computer using a cable. You must also configure the attached to the i3 with an IP address of (x any number from 2-254 since the i3 is 1 as its 4th number). Open the admin page by browsing to with your browser. You will be asked for a username (cti) and password both entered in lowercase. Click the link Configure/Settings Page The configuration page will open with a large red button near the top of the page. Click this large red button and the page will with a large green button. Click the second gray button below the green titled This will take you to a page where the 3rd field from bottom is the current IP address of the i3. Change this IP address field to whichever address given to you by the system administrator. The two fields below are also open for editing. The Size (default value = 8) is the equivalent of a Mask of 255.0.0.0 and the Mask Size of 24 is equivalent of a Subnet Mask of 255.255.255.0. After changing this IP address parameters, click the button to save the changes. After these changes are saved, you must repeat the above to click the large green button in for the i3 to operate properly. Communication (cont Access: some cases, the web pages on the i3 may need to viewed publicly via the internet. Configuration of a or firewall will most likely be necessary. The ports that will need to be opened/routed to the i3 21 (FTP used to transferring files to/from the i3), (TELNET used for a command line interface to the for more complex configuring), and 80 (HTTP used display web pages to your browser). The of these ports is unnecessary if the i3 be standing alone on the internet without a firewall router or in a DMZ. Passwords Username username is the only username in the i3. It is for all configuration needs and has the default of It is highly recommended that change this password upon installation of any i3. change this password, you must open the admin by browsing to 10.0.0.1/admin and clicking the Page. Scroll to the bottom of the and you will see 4 fields followed by a button In the username field, enter the old password field enter In the new field enter the desired new password, and re-enter into the fina

No text preview available.

i3 6412 Installation Instructions 2 05/27/2004 Comm. Bus: the IZAC communication bus to COM2. Use the terminal block to wire only the B+ and B- wires the i3. Wire the B+ wire to the left terminal and the to the right terminal. i3 is shipped with a 5vdc power supply that must be for proper operation. Figure 1 shows the +5V where the power supply plug should be ethernet port on the i3 is used for TCP/IP The RJ-45 connector labeled ETH is the Ethernet port which supports all 10/100 Mbps connections. Tunneling Feature: i3 serial tunneling feature is used in conjunction Solidyne ICMS Windows based programming It allows the ICMS software to connect to IZAC network through the i3. This is done by using M204AN plugged into the serial port COM1 of Figure This tunneling feature used TCP port 7001 along with party software programs for serial-to-IP conversion. more information about this serial tunneling feature, 1 Communication Addressing: i3 ships from the factory with the default IP of 10.0.0.1 easiest method of changing this address is to use built-in configuration web pages of the i3. To these pages you must plug the i3 ethernet cable a hub/switch or directly to a computer using a cable. You must also configure the attached to the i3 with an IP address of (x any number from 2-254 since the i3 is 1 as its 4th number). Open the admin page by browsing to with your browser. You will be asked for a username (cti) and password both entered in lowercase. Click the link Configure/Settings Page The configuration page will open with a large red button near the top of the page. Click this large red button and the page will with a large green button. Click the second gray button below the green titled This will take you to a page where the 3rd field from bottom is the current IP address of the i3. Change this IP address field to whichever address given to you by the system administrator. The two fields below are also open for editing. The Size (default value = 8) is the equivalent of a Mask of 255.0.0.0 and the Mask Size of 24 is equivalent of a Subnet Mask of 255.255.255.0. After changing this IP address parameters, click the button to save the changes. After these changes are saved, you must repeat the above to click the large green button in for the i3 to operate properly. Communication (cont Access: some cases, the web pages on the i3 may need to viewed publicly via the internet. Configuration of a or firewall will most likely be necessary. The ports that will need to be opened/routed to the i3 21 (FTP used to transferring files to/from the i3), (TELNET used for a command line interface to the for more complex configuring), and 80 (HTTP used display web pages to your browser). The of these ports is unnecessary if the i3 be standing alone on the internet without a firewall router or in a DMZ. Passwords Username username is the only username in the i3. It is for all configuration needs and has the default of It is highly recommended that change this password upon installation of any i3. change this password, you must open the admin by browsing to http://10.0.0.1/admin and clicking Configure/Settings Page. Scroll to the bottom of page and you will see 4 fields followed by a button In the username field, enter the old password field enter In the new field enter the desired new password, and re-enter into the final f

No text preview available.

M2 – Universal Controller Document 1 01/2005 Cont Environment 40 to 140 F (4 to 60 C) * 10-90% Relative, noncondensing ** Storage Temperature: -10 to 150 F (-23 to 66 C) Storage Humidity: 0-95% Relative, noncondensing Communication RS-485 3 conductor, 18 guage, shielded, up to 8000ft max. Rate (selectable): 57.6k, 38.4k, 19.2k, 9600, 2400, 1200 Backup 7 year lithium Dimensions 70 mm (2.75 in) 78 mm (3.0 in) 160 mm (6.3 in) Holes: 148.5 mm (5.85 in) Center to Center 1.2 lb Approvals Device: Pending is in the process of UL/CSA approval for the entire M2 family and associated modules. Please use Solidyne UL number E76576 24G9 for all references to agency approvals. Stand Alone Controller M2 is the next generation Universal Controller including real time clock and day calendar. Offering 100% compatibility with controllers, ICMS software and i3 networks, the M2 a seamless upgrade path for existing projects. (8) universal inputs and (8) analog outputs built-in, M2 can be expanded to include (4) or (8) digital using plug-in modules. This modular provides customization of the M2 for any of application. Requirements Voltage: 23 to 28 VAC 50/60 Hz 1.7 VA (without optional plug-in modules) 10.3 VA (all optional plug-in modules used) Voltage Fuse: Resetable fuse rated at 1.1A at 24VAC Inputs: (8) Analog Inputs. be independently configured for thermistor*, digital, or 4-20mA. Thermistor Inputs are 3k, 10k, 100kohm thermistor, Type 3. Outputs: (8) 0-10vdc Analog Outputs*. Can drive down to 10Kohm loads at 10vdc Outputs: to Eight (8) Digital Outputs*. Eight (8) digital outputs would require two (2) plug-in relay modules – REV 1 – 01/2005 Solidyne Corporation 4215 Kirchoff Rd. Rolling Meadows IL 60008 (800) 648-3980 www.solidyne.com MODULE M2-R4) MODULE M2-R4) ON FIG. 1 FOR SELECTIONS [COM] [COM] [COM] [COM] HOT NEUTRAL RS-485 LAN COMM CONNECTION RS-485 LAN COMM CONNECTION RS-485 LAN COMM CONNECTION INPUT #1 INPUT #2 INPUT #3 INPUT #4 INPUT #5 INPUT #6 INPUT #7 INPUT #8 OUTPUT TRANSDUCER POWER 25mA MAX OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 OUTPUT #5 OR IO COMMON (JUMPER SELECTABLE) OUTPUT #6 OR IO COMMON (JUMPER SELECTABLE) OUTPUT #7 OR IO COMMON (JUMPER SELECTABLE) OUTPUT #8 OR IO COMMON (JUMPER SELECTABLE) AND OUTPUT COMMON Installation Notes: sure that BATT JUMPER is place before powering unit with on board POWER unit is powered, ON LED flash 1 second on, 1 off continuously when is operating This flashing as a heartbeat and that the unit on. It will not flash or when unit is off. inserting or removing modules or display such as DU-1, M2 must powered OFF or damage will is internally protected over current by a 1.1 self resetting fuse. will protect the 24VAC powering the M2 being damaged due to the failing internally. +8v output is used for low power Solidyne 1 INPUT JUMPERS (NOTE 2) INPUT LED (NOTE 3

No text preview available.

M2-R4 4 Relay Output Module Document 2 11/2004 1 2 3 4 View View Switch LED Plug-In the module into female mating stability off power to the or M2V before this module Mating on Plug-In Relay Module M2 Plug-In Relay Module is a add-in relay card that the M2 controller family 4 relay outputs. These are designated as outputs 1 through 4 or outputs through 8 and are double pole double throw (DPDT) can be used as normally open (NO) or normally (NC). The module also has HOA switching on each of the four relays as well as a status When the HOA switch is in HAND mode, the LED will have a long ON blink and a very short blink. If the HOA switch is in OFF mode, the LED have a long OFF blink and a short ON blink. In Auto the LED will stay ON or OFF depending on the status. The M2-R4 module can be used on both the M2 and M2V The terminal block on this module has labeled terminals 26, 37 and 48. For example, the first relay of the M2-R4 can be output 1 or 5 depending on where the module is inserted. the module is inserted into the Relay Module Port on the M2V, will designate Relay 1 as the controller Output 5. Then with a marker, the 1 of the 15 label can be blacked out to only show 5. Continue this process for outputs 6, 7 and 8 so that the relay shows the correct output labels. On an M2, two M2-R4 can be used simultaneously to provide outputs 1 through 8. the first M2-R4 module, with a black marker, mark out the 5, 6, 7 and 8 and for the second M2-R4 module, mark out numbers 1, 2, 3 and 4. LED Specifications Ratings: 5A at 24VAC (NO) 3A at 24VAC (NC) Load: 10mA at 6VAC Duty Cycle: 20 cycles per minute Contact Life: 500,000 at 5A (NO) 200,000 at 3A (NC) Consumption: 8.5VA (all relays energized) should not be used to switch more than 24VAC Environment 40 to 140 F (4 to 60 C) * 10-90% Relative, noncondensing ** Storage Temperature: -10 to 150 F (-23 to 66 C) Storage Humidity: 0-95% Relative, noncondensing – REV 2 – 11/2004 Corporation 4215 Kirchoff Rd. Rolling Meadows IL 60008 (800) 648-3980 www.solidyne.com

No text preview available.

No text preview available.

M2V – VAV Controller Document 3 01/2005 Cont Environment 40 to 140 F (4 to 60 C) * 10-90% Relative, noncondensing ** Storage Temperature: -10 to 150 F (-23 to 66 C) Storage Humidity: 0-95% Relative, noncondensing Communication RS-485 3 conductor, 18 guage, shielded, up to 8000ft max. Rate (selectable): 57.6k, 38.4k, 19.2k, 9600, 2400, 1200 Backup 7 year lithium Dimensions 70 mm (2.75 in) 78 mm (3.0 in) 160 mm (6.3 in) Holes: 148.5 mm (5.85 in) Center to Center 1.2 lb Approvals Device: Pending Air Volume Controller M2V is the next generation Variable Air and Temperature Controller. Plug-in modules available for flow sensing, actuator and external control. These plug-in modules allow easy of the M2V for any type of VAV This peer-to-peer, stand alone or VAV controller can control ANY type of air volume unit. Requirements Inputs: Temperature* Temperature* Zone Temperature Setpoint Adjust (ZTS-A) Main Damper Actuator Position Auxiliary Damper Actuator Position Temperature Inputs are 3k, 10k, 100kohm thermistor, Type 3. Outputs: Actuator Output 0-10vdc* Actuator Output 0-10vdc* Can drive down to 10Kohm loads at 10vdc Voltage: 23 to 28 VAC 50/60 Hz 1.7 VA (without optional plug-in modules) 10.3 VA (all optional plug-in modules used) Voltage Fuse: Resetable fuse rated at 1.1A at 24VAC is in the process of UL/CSA approval for the entire M2 family and associated modules. Please use Solidyne UL number E76576 24G9 for all references to agency approvals. – REV 3 – 01/2005 Solidyne Corporation 4215 Kirchoff Rd. Rolling Meadows IL 60008 (800) 648-3980 www.solidyne.com MODULE M2-R4) M2V-FMD) M2V-FMD) HOT NEUTRAL RS-485 LAN COMM CONNECTION RS-485 LAN COMM CONNECTION RS-485 LAN COMM CONNECTION TEMP COMMON TEMP 3/10/100K (INPUT #2) COMMON TEMP 3/10/100K (INPUT #1) ADJUSTMENT POT (INPUT #3) TRANSDUCER POWER 25mA MAX VDC INPUT/OUTPUT COMMON VDC INPUT (INPUT #8) VDC OUTPUT (OUTPUT #3) VDC INPUT (INPUT #7) VDC OUTPUT (OUTPUT #1) (T) (R) ON CFM SENSOR PORT SWITCH ON/HEARTBEAT LED JUMPER M2V-FS) MODULE TYPE 10K, 100K 10K, 100K 1 2 3 4 5 6 7 8 TEMP AIR DAMPER DAMPER 0-10V TABLE BLOCK (9) AIR (10) (15) (13) BOARD BOARD BOARD BOARD BOARD OUTPUT TABLE MODULE 0-10V BOARD BOARD OUTPUT TABLE OUTPUT 1 MAIN ACTUATOR CW 2 ACTUATOR MODULE 3 AUX ACTUATOR CW 4 AUX ACTUATOR CCW 5 6 7 8 OUTPUT OUTPUT OUTPUT OUTPUT FUTURE USE FUTURE USE MUST HAVE 8 PIN RJ-45 TO PROPERLY CONNECT M2V SIDE TERMINAL. DU-1 ALSO HAVE BEEN PURCHASED NOV. 2004. HAS INTERNAL TEMPERATURE THAT SHARES THE SAME AS TEMP SENSOR #1). DU-1 AND TEMP TERMINAL CANNOT BE SIMULTANEOUSLY.

No text preview available.

M2V-FMD Actuator Control Module Document 2 11/2004 CCW C POTB Plug-In Universal Actuator Control Module M2V Plug-In Actuator Control Module is an add on that allows the control of an external floating type for controlling a damper or valve. It can also feedback signal wiring from the actuator. module can be used on both the Main or Auxiliary ports on the M2V mainboard. Table in Main Actuator Port: Controller Input 5* Controller Output 1 Controller Output 2 in Auxiliary Actuator Port: Controller Input 6* Controller Output 3 Controller Output 4 Environment 40 to 140 F (4 to 60 C) * 10-90% Relative, noncondensing ** Storage Temperature: -10 to 150 F (-23 to 66 C) Storage Humidity: 0-95% Relative, noncondensing Plug-In the module into female mating stability Mating on Feedback inputs should be configured for 0-10vdc will provide a data range of 0.0-1000.0 from full position (0.0) and full CCW position (1000.0). Belimo LM24-5P Wiring Module LM24-5P – REV 2 – 11/2004 Corporation 4215 Kirchoff Rd. Rolling Meadows IL 60008 (800) 648-3980 www.solidyne.com

No text preview available.

M2V-FS FLOW SENSOR Document 2 11/2004 Port to Pitot Tube LO port Port to Pitot Tube HI port Port Port the module into female mating stability off power to the before inserting module Mating on Plug-In Flow Sensor Module M2V Plug-In Flow Sensor Module is a add-in pressure transducer that plugs into the Flow port on the M2V. It is used to sense, calculate measure the volume of air in Cubic Feet per Minute flowing into the control zone. 0-1″ W.C. 2% full scale Port: .110″ O.D. Environment 40 to 140 F (4 to 60 C) * 10-90% Relative, noncondensing ** Storage Temperature: -10 to 150 F (-23 to 66 C) Storage Humidity: 0-95% Relative, noncondensing see Application Notes and other supporting documents for module programming and configuration. These can be downloaded at www.solidyne.com – REV 2 – 11/2004 Corporation 4215 Kirchoff Rd. Rolling Meadows IL 60008 (800) 648-3980 www.solidyne.com

No text preview available.

TECH/DATA SHEET Controller sLON-1 Controller is an interoperable controller in accordance with LONMARK guidelines. loaded with a pre-engineered application from WPT Software Tool application library, or using WPT Software Tool, these provide control for packaged rooftops, heat fan coils, unit ventilators, and similar This controller features sLON-WTSx sensor support, one digital input, one universal and three digital outputs. This controller in standalone mode or as part of a network using the integral FT 3150 Free communications transceiver. A direct to a sLON-ADPx Communication adapter a PC with WPT Software Tool is necessary to and modify applications. Chart Controller with Coil Profile (8020) Controller with Pump Profile Controller with Profile (8030) Controller with Profile (8030) Digital Input (DI) Universal Inputs (UI) Digital Outputs (DO) items not provided) carton for damage. If notify carrier Inspect for damage upon must be a technician Job wiring diagrams Corporation – www.solidyne.com rev1 02/2005 Tools: Digital Volt-ohm meter (DVM) Drill and bits for mounting screw Static protection wrist strap Class 2 power transformer supplying a nominal 24 VAC (20.4 to 30 VAC) with a rating of 12 VA, 50/60 Hz per controller, plus Digital Output (DO). Each DO be up to an additional 24VA maximum. In European Community, transformer must to EN 60742 Terminators: One sLON-T1 terminator required for each free topology segment Two sLON-T2 terminators required for each bus topology segment Two #10 sheet metal screws rev1 02/2005 Electrical shock hazard! Disconnect power before installing or removing the Follow Static precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception can be determined by turning the equipment off and on user is encouraged to to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to which the receiver the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/television technician for help. Department of Communications (DOC) class B digital apparatus meets all requirements of the Canadian Interference-Causing Regulations. Community Directives equipment meets all requirements of European Community Directives for Low Voltage General Safety (92/59/EEC), and Electromagnetic Compatibility Avoid locations where excessive

TECH/DATA SHEET Controller sLON-2xx, sLON-3xx, and sLON-4xx (sLON-2, and sLON-4) Controllers are interoperable designed in accordance with LONMARK and equipped with LONMARK HVAC profiles. controllers support sLON-WTSx digital sensors. indicators, a wiring subbase with removable field wiring terminal blocks, as well as DIN or panel mounting ability are other features of these They function in standalone mode or as of a LONWORKS Network using the integral FT Free Topology communications transceiver. A connection to a sLON-ADPx Communication and a PC with WPT Software Tool software is to download and modify applications. Chart Controller with Coil Profile (8020) Controller with Pump Profile Controller with Profile (8030) Controller with Profile (8030) Controller with Coil Profile (8020) Controller with Pump Profile Controller with Profile (8030) Controller with Profile (8030) Controller with Coil Profile (8020) Controller with Pump Profile Controller with Profile (8030) Controller with Profile (8030) Digital Input (DI) Universal Inputs (UI) Digital Outputs (DO) Universal Inputs (UI) Digital Outputs (DO) Analog Outputs (AO) Digital Inputs (DI) Universal Inputs (UI) Digital Outputs (DO) Analog Outputs (AO) Corporation – www.solidyne.com sLON-3xx, sLON-4xx rev1 03/2005 items not provided) carton for damage. If damaged, notify carrier immediately. Inspect controllers for upon receipt. must be a qualified, experienced technician. Job wiring diagrams Tools: Drill and bits for panel mounting screws Digital Volt-ohm meter (DVM) Static protection wrist strap Class 2 power transformer supplying a nominal 24 Vac (20.4 to 30 Vac) with a minimum of 15 Va, 50/60 Hz per controller plus Digital Output (DO) loads (if same is used). In European Community, transformer must conform to EN 60742 Terminators: One sLON-T1 terminator required for each free topology segment Two sLON-T2 terminators required for each bus topology segment Two #6 pan head panel mounting screws or 35mm DIN rail for mounting sLON-3xx, sLON-4xx rev1 03/2005 Electrical shock hazard! Disconnect power before installing or removing the Follow Static precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception can be determined by turning the equipment off and on user is encouraged to to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment to an ou

No text preview available.

TECH/DATA SHEET VAV Controller a n d la cla B re to le e d R s le m bro d C Cla B digital a m all re of th C Interfere E R th m c u o m n c h interfere a (2) T d m a a interfere re in d c with P 1 of th F R O is s to th follo tw c (1) T A E in a 5 M Cla 2. 1 M Cla 2. 2 3 M C f = 0.4. 2 0.4 M Total L Te -4 to + + D lo 2 5 Cla 2, 0 0 a n d la cla B re to le e d R E R Cla B digital a m all re of th C Interfere c u o T d m a a interfere re in interfere th tw c (1) T d m n c h interfere a d c with P 1 of th F R O is s to th A E P B S S C 2 CIR O E S O FIR D N E in a 0 0 2 = 0.4 3 M 5 M Cla 2 1 M Cla 2 2 0.4 M Total L Te -4 to + + D lo 2 5 Cla 2, sLON-5 and sLON-6 Controllers are interoperable designed in accordance with LONMARK When programmed using WPT Software these controllers provide control for fan coil and ventilator applications. These controllers feature: terminal blocks; three universal inputs, to respond to one of five input one (sLON-5) or three (sLON-6) high-voltage output(s); four 24 Vac Triac (digital) outputs; and S-Link interface for connection to an optional digital senso

No text preview available.

No text preview available.

TECH/DATA SHEET Controller Enclosure 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 H G Card Enclosure sLON-7 Controllers are programmable, LONWORKS based control devices. sLON-7 Series Controller features eight universal four analog outputs, eight digital outputs, a volt reference, LED indication, and support for sensors. Additionally, network capability provided through the use of a FTT-10 transceiver the controller to communicate to other devices part of a LONWORKS Free Topology network. A direct connection to a Communication adapter and a PC with Software Tool is necessary to download and applications applications include central station air VAV air handlers, fan coil units, unit and cooling towers. Chart Wall-Mount Enclosure Enclosure Card with Backed-up Time items not provided) carton for damage. If notify carrier Inspect for damage. damaged products must be a experienced Job wiring diagrams Tools: Drill and bits for Corporation – www.solidyne.com rev1 03/2005 mounting screws Digital Volt-ohm meter (DVM) Static protection wrist strap Class 1 or Class 2 power transformer supplying a nominal 24 Vac (20.4 to 30 Vac) with minimum rating of 20 VA, 50/60 Hz per controller plus Digital Output (DO) loads (if transformer is used). In European Community, transformer must conform to standards. Terminators: One sLON-T1 terminator required for free topologies Two sLON-T2 terminators required for bus topologies Electrical shock hazard! Disconnect power before installing or removing the Follow Static precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception can be determined by turning the equipment off and on user is encouraged to to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to which the receiver the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/television technician for help. Department of Communications (DOC) class B digital apparatus meets all requirements of the Canadian Interference-Causing Regulations. appareil numerique de la classe [B] respecte toutes les exigences du Reglement sur le broilleur du Canada. Community Directives equipment meets all requirements of European Community Directives for Low Voltage and Electromagnetic Compatibility (89/336/EEC).

TECH/DATA SHEET VAV Controller sLON-V1 and sLON-V2 VAV Controllers are LONMARK variable air volume These controllers provide pressure control for cooling and reheat They feature a built-in actuator with over- damper mounting, an integral velocity transducer, LED indication, support for an digital sensor, push-button manual mechanical position indication, and an easy- mechanical travel limit. They function in mode or as part of a LonWorks network the integral FTT-10 Free Topology transceiver. A direct connection to a Communication adapter and a PC with Software Tool software is necessary to download modify applications. Chart Inputs Outputs Type Floating/ denotes LONMARK VAV (Variable Air Volume) profile and profile version Cooling Series Fan Induction Parallel Fan None Staged Electric Time Reheat None Occupancy Satellite Corporation – www.solidyne.com sLON-V2x rev1 03/2005 items not provided) carton for damage. If damaged, notify carrier immediately. Inspect controllers for Return damaged products. must be a qualified technician Job wiring diagrams Tools: AM-340, T-25 Torx short arm key (L-shaped wrench), or T-25 Torx bit with 1/4 in. hex shank (for use with socket wrenches) 1/4 inch hex driver for travel adjustment screws Pliers for turning damper shafts Digital Volt-ohm meter (DVM) Drill and bits for mounting screw Static protection wrist strap Torque wrench (capable of measuring at least 32 in-lb (0.37 Kg-meters)) AM-135, 3/8 in. (9.5mm) to 1/2 in. (12.8mm) shaft adapter (optional) Class 2 power transformer supplying a nominal 24 Vac (20.4 to 30 Vac) with a minimum of 12 VA, 50/60 Hz per controller plus Digital Output (DO) loads. Each DO can be to 24 VA. In European Community, transformer must conform to EN 60742 Terminators: One sLON-T1 terminator required for free topologies Two sLON-T2 terminators required for bus topologies One #10 sheet metal screw 0.170 in.(17/100) I.D. FRPE polyethylene tubing or 0.125 in. (1/8) I.D. or 0.25 in. (1/4) tygon tubing for piping connections. Not more than five feet (1.52m) long. Electrical shock hazard! Disconnect power before installing or removing the Follow Static precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception can be determined by turning the equipment off an

No text preview available.

No text preview available.

TECH/DATA SHEET VAV Controller sLON-V3 VAV Controllers are interoperable variable air volume controllers. controllers provide pressure independent for cooling and reheat applications. The sLON- features sLON-WTSx Digital Sensor support, LED three digital relay outputs, an integral pressure transducer, and two triac outputs for with an external actuator. This controller in standalone mode or as part of a LonWorks using the integral FTT-10 Free Topology transceiver. A direct connection to a Communication adapter and a PC with Software Tool software is necessary to download modify applications. Chart Digital Analog Triac (UI) Digital (DI) Strategy Config Type Cooling Series Fan Parallel Induction Staged Floating/ Time None Occupancy Satellite denotes LONMARK VAV (Variable Air Volume) profile and profile version Corporation – www.solidyne.com rev1 03/2005 items not provided) carton for damage. If damaged, notify carrier immediately. Inspect controllers for Return damaged products. must be a qualified technician Job wiring diagrams Tools: Digital Volt-ohm meter (DVM) Drill and bits for mounting screw Static protection wrist strap Class 2 power transformer supplying a nominal 24 VAC (20.4 to 30 VAC) with a rating of 12 VA, 50/60 Hz per controller, plus Digital Output (DO) and Triac Each DO can be up to an additional 24VA maximum and each Triac load an 18VA maximum. In European Community, transformer must conform to 60742 Terminators: One sLON-T1 terminator required for free topologies Two sLON-T2 terminators required for bus topologies Two #10 sheet metal screws 0.170 in. (17/100) I.D. FRPE polyethylene tubing or 0.125 in. (1/8) I.D. or 0.25 in. (1/4) tygon tubing for piping connections. Not more than five feet (1.52m) long. Electrical shock hazard! Disconnect power before installing or removing the Follow Static precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception can be determined by turning the equipment off and on user is encouraged to to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment to an outlet on a circuit different from that to which the receiver the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/television technician for help.

No text preview available.

TECH/DATA SHEET Temperature Sensors sLON-WTS Sensors are wall-mounted digital and humidity sensors for use with Controllers. These sensors feature Sensor Link communication protocol that provides a simple wire interface for power and exchange of sensor subbase information. Available in twelve models, sLON-WTS Sensors provide integral analog to conversion for elimination of electrical between sensor and controller. An wiring connection allows access to the network (LON via a LONWORKS network on the left side of each sensor. This jack allows connection to a PC running the WPT Software or a third party Network Management Tool. Each also provides an S-Link jack on the right side for to a PDA running Pocket sLON software. Sensors are suitable for direct-wall, 2 x 4 box, 1/4 DIN electrical box, or surface box Chart Table-1 on page 2 for a chart of the models. Corporation – www.solidyne.com rev1 04/2005 sLON-WTSx Model Chart. and Sensor only with override Sensor with setpoint adjustment and override Sensor with setpoint, override, and controller functions Sensor with setpoint, On/Off and Fan speed Sensor with setpoint, override, controller mode and emergency heat key displays value and setpoint. Allows viewing of alarms and diagnostics. displays values, setpoints, and controller mode functions. Override Status Indication LCDa and LED Override Status LCDc and LED Override Status LCDc and LED Fan Status LCDc, LED Override Status, and Heat Indication sLON-WTS Sensor is packaged disassembled in one box and consists of three major A pre-wirable base plate for wiring to the controller S-Link and LonWorks network (LON) An electronic assembly containing the sensors and associated circuitry A removable cover carton for damage. If damaged, notify carrier immediately. Inspect sensors for upon receipt. must be a qualified technician items not provided) Job wiring diagrams Tools: Drill and bits for mounting screws Level Static protection wrist strap Two mounting screws (dry-wall anchors for direct-wall mount) Disconnect power before installing or removing the cover. to observe this warning can damage the sensor. Follow Static Precautions when installing this equipment. Use copper conductors that are suitable for 167 (75 Make all connections according to electrical wiring diagram, national and local electrical Precautions charges damage electronic components. The microprocessor and associated circuitry extremely sensitive to static discharge. Use the following precautions when installing, or operating the system. Work in a static-free area. Discharge static electricity by touching a known, securely grounded object. rev1 04/2005 Use a wrist strap connected to earth ground when handling the controller printed board. Communications Commission (FCC) equipment has been tested and found to comply with the limits for a Class B digital pursuant to Part 15 of the FCC Rules. These limits are designed to provide protection against harmful interference in residential installations. This generates, uses, and can radiate radio frequency energy and may cause harmful if not installed and used in accordance with the instructions. Even when are followed, there is no guarantee that interference will not occur in a particular If this equipment causes harmful interference to radio or television reception

No text preview available.