Fire-Lite ANN-80C 80-Character LCD Fire Alarm Indicator (Canadian)

ANN-80C Serial LCD Indicator ANN-80C indicator is a compact, backlit, 80-character LCD fire that mimics the Fire Alarm Control Panel (FACP) display. It system status indicators for AC Power, Alarm, Trouble, and Alarm Silenced conditions. The ANN-80C and the communicate over a two-wire serial interface employing the communication format. Connected devices are powered, two additional wires, by either the host FACP or a remote ULC- filtered power supply. The ANN-80C is red. ANN-80C displays English-language text of system point infor- including device type, zone, independent point alarm, trouble supervisory status, as well as any custom alpha labels pro- into the control panel. It includes buttons for local silence, test, and sounder test. A keyswitch prevents unauthorized to eight ANN-80Cs may be connected to the ANN-Bus of each No programming is required, which saves time during system ULC listed meets all Canadian requirements for a fire alarm Backlit 80-character LCD display (20 characters x 4 lines) Buttons for local silence, lamp test, and sounder test Keyswitch enables/disables buttons and mechanically locks indi- enclosure Keyswitch can be enabled or disabled at the FACP Enclosure supervised for tamper System status LEDs for AC Power, Alarm, Trouble, Supervisory, Alarm Silence Local sounder can be enabled or disabled at the FACP ANN-80C connects to the ANN-BUS terminal on the FACP and minimal panel programming Displays device type identifiers, individual point alarm, trouble, zone, and custom alpha labels Time-and date display field Surface mount directly to wall or to single, double, or 4″ square box Semi-flush mount to single, double, or 4″ square electrical box. ANN-SB80KIT for angled view mounting Can be remotely located up to 1,800 m from the panel Backlight turns off during AC loss to conserve battery power but turn back on if an alarm condition occurs May be powered by 24 VDC from the host FACP or by remote supply (requires 24 VDC) and Indicators AC Power Alarm Trouble Supervisory Alarm Silenced Local Silence Lamp Test Sounder Test DF-60676:A2 Operating voltage range: 18 VDC to 28 VDC Current consumption @ 24 VDC nominal (filtered and non- 40 mA maximum Ambient temperature: 0 to 49 Relative humidity: 93% 2% RH (non-condensing) at 32 13.65 cm. high x 17.46 cm. wide x 3.49 cm. deep For use indoors in a dry location All connections are power-limited and supervised ANN-Bus THE DEVICES ON THE ANN-BUS FROM AUXIL- POWER SUPPLY ANN-Bus can be powered by an auxiliary power supply when maximum number of ANN-Bus devices exceeds the ANN-Bus requirements. See the FACP manual for more information. DEVICE ADDRESSING ANN-Bus device requires a unique address (ID Number) in to communicate with the FACP. A maximum of 8 devices can connected to the FACP ANN-Bus communication circuit. See the manual for more information. REQUIREMENTS: COMMUNICATIONS CIRCUIT ANN-80C connects to the FACP ANN-Bus communications cir- To determine the type of wire and the maximum wiring distance can be used with FACP ANN-Bus accessory modules, it is nec- to calculate the total worst case current draw for all modules a single 4-conductor bus. The total worst case current draw is by adding the individual worst case currents for each For total worst case current draw on a single ANN-Bus refer to FACP manual. 3/15/2018 Page 1 of 2 REQUIREMENTS: POWER CIRCUIT 14 to 18 AWG (0.75 – 2.08 mm2) wire for 24 VDC power circuit is Power wire distance limitation is set by 1.2 volt maxi- line drop form source to end of circuit. All connections are power-limited and supervised. A maximum of eight ANN-80C modules may be connected to this Options Red 80 character LCD Indicator. Red surf