Fire-Lite ECC-50(E)_100(E)

ECC-50/100(E) Command Center ECC-50/100 and ECC-50/100E are multipurpose emer- voice evacuation panels for fire applications, mass notification or both. The Primary Operating Consoles (POCs) 50 or 100 watts of audio power for distribution to up to eight circuits (i.e. zones). The ECC-50/100(E) comes standard a single speaker circuit and a built-in 25Vrms, 50 watt amplifier. secondary 50 watt amplifier (ECC-50W-25/70V) can be added for speaker circuit backup or to increase system capacity to two circuits and an additional 50 watts of audio power. An ECC-CE6 module added to the ECC-50/100(E) will upgrade system to a maximum of eight speaker circuit outputs. All output circuits can be wired in either Style Y (Class B) or Z (Class A) configuration. The ECC-50/100(E) has fourteen programmable messages (up to 60 seconds each), built-in field pre- and post-announce tone generators and a fully Notification Appliance Circuit (NAC) with 2.0 amps of NAC power. The ECC-50/100(E) includes three built- Form-C relay contacts, (AC power, trouble and MNS active) a follower input for triggering the on board NAC circuit and special application power. A built-in power supply with switch technology delivers operational power to the panel and an battery charger supports charging up to 26AH batteries cabinet holds up to 18AH batteries). fire protection applications, the ECC-50/100(E) is an adjunct to any UL listed FACP, providing reverse polarity or contact can be used as a stand-alone unit for non-fire applications. seamless integration between fire and mass notification, the can be directly activated via serial communication the ES-200X, MS-9600(UD)LS, or MS-9200UDLS. Activa- of the ECC-50/100(E) via other FACPs uses the eight on board Input Circuits (CMDs). Two of the eight CMD circuits 1 & CMD 2) can be individually field programmed for activa- by an FACP Notification Appliance Circuit reverse polarity and eight can be activated by a contact closure. In addition, the ECC- can be activated from a building Private Branch (PBX) with the integral night ring feature. ECC-50/100(E) programming is done by using a simple, built-in utility accessed from any laptop. For added flexibility, ECC-50/100(E) supports both 25Vrms and 70.7Vrms speaker operation. By adding a 70V transformer conversion module or an additional 70.7 volt secondary amplifier the system supports 70.7 volt speaker devices. ECC-50/100(E) can expand in order to accommodate larger or complex installations. To add more control and increase sys- capacity, any combination of up to eight external remote con- (including the ECC-LOC, ECC-RPU, and ECC-RM) and up to distributed audio amplifiers (including the ECC-50DA(E), ECC- and ECC-125-DA(E) can be connected on the external data and audio riser data bus to create a fully integrated command A fully loaded system supports up to 1100 watts of total audio and up to 24 speaker circuit outputs. APPLICATIONS Schools Theaters Auditoriums Dormitories Healthcare Facilities Military facilities Places of Worship Factories Office Buildings Restaurants C-200 Communications UL Listed to UL 2572 Communication (Control Units Mass Notifi- Systems) and UL 864 (emergency voice evacuation for Modular design for system flexibility and easy expansion Removable terminal blocks for ease of servicing and module 50 watts of 25V audio power (expandable to 100 watts) RMS 2 amp Notification Appliance Circuit (NAC) output, sync genera- or follower for System Sensor, Wheelock or Gentex protocols Optional 70.7VRMS conversion transformer available for the pri- amplifier. (Note that speaker wiring continues to be super- in standby, alarm and when background music is playing this optional transformer installed) Eight Command Input Circuits to activate messages 1 to 8: CMD1 and CMD2 are field selectable to be activated from 12 or VDC Notification Appliance Circuits (reverse polarity) or con- closures CMD3-CMD8 are a