Fire-Lite Intelligent Bases

Intelligent Bases Relay, Isolator, Sounder, Low-Frequency Sounder Bases meet local code and application requirements, Fire-Lite offers 4″ and 6″ bases, as well as, specialty base designs includ- relay, isolator, sounder and low frequency sounder options for new 365 Series of addressable detectors as well as previous standard 4″ and 6″ bases offer a plug-in detector base intended use in intelligent systems, with screw terminals provided for (+ and and remote annunciator connections. Communica- takes place over the power (+ and lines. The 4″ base offers a design while the 6″ base provides compatibility with a wider of junction boxes. specialty bases support application driven requirements. These employ a separate mounting plate that installs on various box sizes to eliminate unsightly surface-mount boxes. The plate enables pre-wiring of all connections to speed and installation. bases (B224RB-WH/B224RB-IV) provide one form-C contact for control of auxiliary functions, such as door closure and ele- recall. The relay can operate in two different modes (short and delay). The activation time for the short delay is 60-100 milli- while the activation time for the long delay is 6-10 sec- A shunt with pin headers, located on the base PC board, is to set the delay timing. bases (B224BI-WH/B224BI-IV) allow the Signaling Line Cir- (SLC) loop to operate under fault conditions created from a circuit preventing an entire communication loop from being dis- The base isolates the section of the loop containing the short from the remainder of the circuit and automatically restores the fault is corrected. and low frequency (-LF) sounder bases are designed for and existing dwelling unit applications. They offer maximum in installation, configuration, and operation to meet or UL 268 and UL 464 requirements. The low frequency bases are designed to meet the NFPA 72 sleeping space to produce a fundamental frequency of 520 Hz +/- 10% a square wave or its equivalent. Studies show that a lower fre- centered around 520 Hz, is the most ideal to wake sleeping even those with mild to severe hearing loss. B200SR sounder and -LF sounder bases (B200SR-WH/ are fully compatible existing B501BH Series sounder base installations. The device users to select one of two B501-supported tones (ANSI 3 or Continuous) through a jumper. B200S sounder and -LF sounder bases (B200S-WH/B200S-IV/ adopt the same address as the detec- but use a unique device type on the loop. The Fire Alarm Control (FACP) can use that address to command an individual or a group of sounders to activate. The command set the FACP can be tailored to multiple event-driven tone outputs selection of volume (75 or 85 dBA), tone (ANSI Temporal 3, Temporal 4, or March Time) and group. In addition, some will enable custom tone patterns. The B200S series sounder recognize the System Sensor synchronization protocol. This them to be used as a component of the general evacuation along with other System Sensor AV appliances when to a power supply or FACP output capable of generating System Sensor synchronization pulses. E-265 Devices Standard Base (White) Standard Base (Ivory) Base (White) Low- Sounder Base (White) Flangeless Base (White) Flangeless Base (Black) Specifications applies to all model variants -WHITE. See Product Line Information for detailed model descrip- B501-WHITE: 4″ (10.16 cm) diameter. B300-6: 6.1″ (15.49 cm) diameter. B224BI, B224RB: 6.2″ (15.748 cm) diameter. B200S, B200SR: 6.875″ (17.46 cm) diameter. gauge: B224BI, B224RB: 14 to 24 AWG. B300-6, B501, B200S, B200SR: 12 to 24 AWG range: B224BI, B224RB, B200S, B200SR: 32 to 120 (0 to 49 B300-6, B501: -4 to 150 (-20 to 66