Fire-Lite ISO-6 Six Fault Isolator Module

ISO-6(A) Fault Isolator Module ISO-6(A) Six Fault Isolator Module provides six equivalent that will allow a portion of the communications loop to operating when a short circuit occurs on that loop. An LED indicator will blink in the normal state for each of six inputs and will latch on during a short circuit condition. module will automatically restore the communications to normal condition when the short circuit is removed. ISO-6 Six Isolator Module is an automatic switch that when the line voltage drops below four volts. Isolator should be spaced between groups of sensors or in a loop to protect the rest of the loop. If a short between any two isolators, then both isolators immedi- switch to an open circuit state and isolate the devices them. The remaining units on the loop continue to operate. LED status indicators. Removable 12 to 18 AWG plug-in terminal blocks. Six individual, Class B isolator circuits. Mount up to two modules in BB-2F enclosure (optional). Mount up to six modules on a CHS-6 chassis in a BB-6F Mounting hardware included. ISO-6 Fault Isolator Modules should be spaced between of sensors in an SLC to protect the rest of the loop. to isolate short circuit problems within a section of a loop that other sections can continue to operate normally. The supports a maximum of 25 devices between isolators. more than 100 Isolator Modules are connected to an loop, the address capacity of the loop is reduced by two addresses for every isolator device in excess of 100. Operating Voltage: 15-32 VDC. Current: 450 per circuit, 2.7 mA all circuits. Current Draw: 17 mA per circuit in isolation, 102 with all circuits in isolation. Range: 32 F to 120 F (0 C to 49 C). 10% to 85% non-condensing. 6.8″H x 5.8″W x 1.0″D. weight: 1.1 lb. (0.50 kg) including packaging. Options: CHS-6 Chassis, BB-2F Cabinet, BB-6F Gauge: 12 AWG (3.31 mm to 18 AWG (0.821 mm Devices: See the documentation for your panel, the Fire-Lite Device Compatibility Document. Devices Listings and Approvals listings and approvals below apply to ISO-6 components. In cases, certain modules or applications may not be listed certain approval agencies, or listing may be in process. Con- factory for latest listing status. UL/ULC Listed: S3705. FM Approved. CSFM: 7300-1653-0234. Line Information Six Isolator Module. ULC-listed version of ISO-6. Optional cabinet for one or two modules. Door Dimen- 9.234″ (23.454 cm) wide (9.484″ [24.089 cm] including x 12.218″ (31.0337 cm) high, x 0.672″ (1.7068 cm) Backbox Dimensions: 9.0″ (22.860 cm) wide (9.25″ cm] including hinges), x 12.0″ (30.480 cm) high x 2.75″ cm). Chassis Dimensions (installed): 7.150″ (18.161 wide overall x 7.312″ (18.5725 cm) high interior overall x (5.4762 cm) deep overall. Optional cabinet for up to six modules mounted on chassis (below). Door Dimensions: 24.0″ (60.96 cm) x 12.632″ (32.0852 cm) high, x 1.25″ (3.175 cm) deep, at bottom. Backbox Dimensions: 24.0″ (60.96 cm) x 12.550″ (31.877 cm) high x 5.218″ (13.2537 cm) deep. Chassis, mounts up to six modules in a BB-6F cabi- 2/3/2015 Page 1 of 2 is a registered trademark of Honeywell International Inc. by Honeywell International Inc. All rights reserved. Unauthorized use this document is strictly prohibited. document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. cannot cover all specific applications or anticipate all requirements. specifications are subject to change without notice. more information, contact Fire(cid:129)Lite Alarms. Phone: (800) 627-3473, FAX: (877) 699-4105. 2 of 2 DF-60845:A (cid:129) 2/3/2015