Fire-Lite LDM Lamp Driver Module

May 12, 1998 Series Driver Modules Annunciators Fire 2000) 2000) LDM Series Lamp Driver Modules, when combined with a cus- graphic display, provide annunciation and control for the 2000 and MicroScan-9200 fire alarm control panels. modules use a serial communications interface, and may be up to 6,000 feet from the panel. ALARM/CIRCUIT ON and TROUBLE lamp/LED per-point option, more dense alarm-only option (field-selectable). Control switch option for remote control per point. Lamps/LEDs may be programmed to display status of notification or control relays as well as system status conditions. System trouble lamp/LED signal. On-line/power LED indicator. Alarm and trouble resound with flash of new conditions. Local sounder for both alarm/circuit-on and trouble conditions with switch connection. Serial EIA-485 interface for reduced installation cost. May be powered by 24 VDC from the panel or by remote power Efficient switched-power converter reduces power consumption. Microprocessor-controlled electronics, fully supervised. Plug-in terminal blocks for ease of installation and service. Trouble monitor option for remote power supplies. basic models are available: the LDM-32F control module and LDM-E32F expander module. Each may be selected to provide alarm indications; or 16 alarm, 16 trouble, and 16 control points. LDM-32F/LDM-E32F with a custom graphic array may be used indicate point status and, in some versions, to control the state of points. LDM-32F and LDM-E32F modules mount on four standoffs in- the custom annunciator graphic box. Alternately, the modules be installed in a standard CHS-4 chassis (Sensiscan 2000), or in an ABS-8RF backbox (when used with the MS-9200). module size is approximately 4.4″ (11.2 cm) x 7.1″ (18 cm). between the LDM Series annunciators and the host Alarm Control Panel are made through a two-wire EIA-485 multi- loop, and a two-wire regulated 24 VDC power loop. Up to 32 systems may be connected to a single control panel. field-wiring terminations use removable, compression-type ter- blocks for ease of installation, wiring, and circuit testing. document is not intended to be used for installation purposes. We try to keep our information up-to-date and accurate. We cannot cover all specific applications or all requirements. All specifications are subject to change without notice. For information, contact Fire(cid:149)Lite. Phone: (203) 484-7161 FAX: (203) 484-7118 Clintonville Road, Northford, Connecticut 06472 and Manufacturing System Certified to Standard ISO-9001 in the U.S.A. (cid:151) Page 1 of 2 Series Lamp Driver Modules are used to provide the Fire(cid:149)Lite Sensiscan 2000 MicroScan-9200 with an interface to a custom graphic annunciator. or remote power supplies and serial communications allow the custom annun- to be located virtually anywhere on the protected premises. system alarm and/or trouble conditions may be annunciated on a per-point or in a grouped-zone configuration. of system operational controls, such as Signal Silence, System Reset, and annunciation controls (such as Local Acknowledge), and Lamp Test may be through special key- or push-switches. LINE INFORMATION Lamp Driver Module with 32 alarm lamp-driver transistors (sink to power on alarm). May be selected (dip switch) for 16 alarm/circuit on, 16 trouble, 16 switch inputs if desired. Also includes system-trouble lamp driver and lamp- switch input. Integral piezo sounder sounds for each new or trouble and is silenced with the Local Acknowledge switch, or permanently with a dip-switch selection. Flash of new alarms or troubles is selectable dip switches. 16 switch inputs may be used for panel SILENCE, RESET, ACKNOWLEDGE, or remote output control (NACs and relays, Sensiscan 2000 Instructions are included. Lamp Driver Module with 32 alarm drivers; or 16 alarm, 16 trouble,