Home » Fire-Lite MS 424 Fire Alarm Control Panel
File preview
Click the button below to download immediately for free
Show text preview
firealarmresources.com Device Connection (Typical) 3: Supervised Class B Operation Detection loop specifications Class B standby: 23VDC current: 15mA circuit current: 35mA current: 5mA resistor: 4.7k, 5% loop resistance: 200 ohms detector current: 2.0mA/Zone Smoke and ionization detectors requiring separate 24VDC can be powered from MCB-104 terminals 12 (+) & 13 (-). Use relay (SDLR-B) to supervise power circuit wiring. Detector loop current is sufficient to ensure operation of one detector per zone. Compatible, U.L. listed, 2-wire detectors available from Fire-Lite. Initiating devices include: Manual stations, heat detectors, smoke detectors, ionization detectors, waterflow alarm devices, manual stations. Use mechanical water motor gong if waterflow alarm devices are connected to the zone. Inhibit latching circuit by removing diode marked with a * from DZC-2 card if coded manual stations are connected. Compatible, U.L. listed, 2-wire detector available from Fire-Lite, include the following series: CP101, CP204, CP311, CP751, SD12T and SD32T. Bell Circuit 5 Modes of operation For non-disconnectable bells, remove jumper J3 but leave jumper J2. For disconnectable bells remove jumper J2 but leave jumper J3. For MTC bell signal, remove jumper J1. Select normally open or normally closed trouble contact by removing J4 or J5 respectively. Trouble contact is provided Terminals 1 and 2. It is rated 2 amps, 28 VDC. a) Connect signalling circuit as shown. Size wire for a maximum voltage drop of 2 VDC. Use polarized, U.L. listed, signalling devices with a minimum rated voltage range of 18 to 30 VDC. For bell power, connect terminal 7 (positive input CKT A), terminal 8 (positive input CKT B) of BCM-2 to terminal 10 & of MCB-104 respectively. Maximum bell load is 1.1 amps per CKT. current load on regulator (add last column) current should not exceed 0.75 amp. unfiltered, unregulated bell power = 2.2 amps total. Remove both jumpers in DZC-2 card(s) if optional module(s) employed. 2: Standby Battery Requirements Remove both jumpers in DZC-2 card(s) if optional module(s) employed. 3: Calculate Ampere-Hour
firealarmresources.com Device Connection (Typical) 3: Supervised Class B Operation Detection loop specifications Class B standby: 23VDC current: 15mA circuit current: 35mA current: 5mA resistor: 4.7k, 5% loop resistance: 200 ohms detector current: 2.0mA/Zone Smoke and ionization detectors requiring separate 24VDC can be powered from MCB-104 terminals 12 (+) & 13 (-). Use relay (SDLR-B) to supervise power circuit wiring. Detector loop current is sufficient to ensure operation of one detector per zone. Compatible, U.L. listed, 2-wire detectors available from Fire-Lite. Initiating devices include: Manual stations, heat detectors, smoke detectors, ionization detectors, waterflow alarm devices, manual stations. Use mechanical water motor gong if waterflow alarm devices are connected to the zone. Inhibit latching circuit by removing diode marked with a * from DZC-2 card if coded manual stations are connected. Compatible, U.L. listed, 2-wire detector available from Fire-Lite, include the following series: CP101, CP204, CP311, CP751, SD12T and SD32T. Bell Circuit 5 Modes of operation For non-disconnectable bells, remove jumper J3 but leave jumper J2. For disconnectable bells remove jumper J2 but leave jumper J3. For MTC bell signal, remove jumper J1. Select normally open or normally closed trouble contact by removing J4 or J5 respectively. Trouble contact is provided Terminals 1 and 2. It is rated 2 amps, 28 VDC. a) Connect signalling circuit as shown. Size wire for a maximum voltage drop of 2 VDC. Use polarized, U.L. listed, signalling devices with a minimum rated voltage range of 18 to 30 VDC. For bell power, connect terminal 7 (positive input CKT A), terminal 8 (positive input CKT B) of BCM-2 to terminal 10 & of MCB-104 respectively. Maximum bell load is 1.1 amps per CKT. current load on regulator (add last column) current should not exceed 0.75 amp. unfiltered, unregulated bell power = 2.2 amps total. Remove both jumpers in DZC-2 card(s) if optional module(s) employed. 2: Standby Battery Requirements Remove both jumpers in DZC-2 card(s) if optional module(s) employed. 3: Calculate Ampere-Hour