Fire-Lite MS-5UD-3_MS-10UD-7(E)

MS-5UD-3/MS-10UD-7(E) Zone Fire Alarm Control Panel Zone Fire Alarm Control Panel MS-5UD-3 is a five-zone FACP (Fire Alarm Control Panel) the MS-10UD-7(E) is a ten-zone FACP. These control pan- provide reliable fire signaling protection for small to commercial, industrial, and institutional build- Both panels include built-in communicators for Central Service and remote upload/download. of these FACPs is compatible with System Sensor i3 series detectors. These conventional detectors can transmit a maintenance trouble signal to FACP indicating the need for cleaning and a supervisory signal when the ambient temperature falls below the rating. Additionally, both the MS-5UD-3 and MS- are compatible with conventional input devices such two- and four-wire smoke detectors, pull stations, waterflow tamper switches, and other normally-open contact Refer to the Fire Device Compatibility Document a complete listing of compatible devices. include four NACs (Notification Appliance Circuits), programmable Form-C relays (factory programmed for Trouble, and Supervisory) and 24 VDC special applica- resettable and nonresettable power outputs. The FACPs all wiring, AC voltage, battery level and telephone integrity. of a compatible smoke detector or any normally- fire alarm initiating device will activate audible and visual devices, illuminate an indicating LED, sound the sounder at the FACP, activate the communicator and alarm relay, and operate an optional module used to a remote station or initiate an auxiliary control function. options include a UL listed printer, PRN-6F and FireLite IPDACT Internet Monitoring module. The IPDACT permits of alarm signals over the Internet saving the cost of two dedicated business telephone lines. not required, the secondary telephone line may be providing backup communication over the public telephone line. The MS-10UD-7E offers the same features as the MS- but allows connection to 240 VAC. Unless otherwise the information in this data sheet applies to both the 120 and the 240 VAC versions of these panels. Listed to UL Standard 864, 9th edition. Built-in DACT (Digital Alarm Communicator/Transmitter). Style B (Class B) IDC (Initiating Device Circuit) MS-5UD-3 – five IDCs. MS-10UD-7 – ten IDCs. application power MS-5UD-3 – four NACs. MS-10UD-7 – four NACs. Notification Appliances may be programmed as Silence Inhibit. Auto-Silence. Strobe Synchronization for System Sensor, Wheelock, Faraday, or Amseco devices. (cid:129) A3-20 Selective Silence (horn-strobe mute). Temporal or Steady Signal. Silenceable or Nonsilenceable. Optional CAC-5X Style Z (Class A) Converter Module for and IDCs (2 required for MS-10UD-7). Form-C Relays for Alarm, Trouble and Supervisory – Con- Ratings 2.0 [email protected] 30 VDC or 30 VAC (resistive). 3.0 A total system current for MS-5UD-3. 7.0 A total system current for MS-10UD-7. Optional Dress Panel DP-51050 Optional Trim Ring TR-CE for semi-flush mounting. 24 volt operation. Low AC voltage sense. Alarm Verification. PAS (Positive Alarm Sequence). Automatic battery trickle charger. Up to eight ANN-BUS annunciators: Optional 8 zone Relay Module ANN-RLY. Optional LED Annunciator Module ANN-LED, Optional Remote Annunciator ANN-80. Optional Remote Printer Gateway ANN-S/PG. Optional LED Annunciator Driver ANN-I/O. Optional 4XTMF module (conventional reverse polarity/city AND SOFTWARE: Can be programmed at the panel with no special software additional equipment. Programmable Make/Break Ratio. Upload/Download (local or remote) of program and data via DACT. 07/10/08 Page 1 of 4 Style Y (Class B) NAC (Notification Appliance Circuit) – spe- transmitter). INTERFACE: Built-in DACT (Digital Alarm Communic