Fire-Lite SEP-SW(A), SEP-SPSW(A) Dual Strobe Expander Plates for Emergency Communications

SEP-SW(A), SEP-SPSW(A) Strobe Expander Plates for Communications new SpectrAlert Advance Dual Strobe and Dual Strobe Speaker Expander Plates lower costs and improve aes- by performing the functions of 2-3 devices for emer- communications applications. costs, speed installation, and improve aesthetics on emer- communications applications that require fire and emer- warnings by combining the functions of two to three on a single mounting plate and back box. SpectrAlert Dual Strobe and Dual Strobe with Speaker Expander provide dual strobe and speaker strobe functionality easy for a single person to wire and install. Simply mount plate to a junction box and connect the field wiring to the To complete the installation, hinge and attach the or speaker strobe device with a single captured mount- screw. Strobe and Dual Strobe with Speaker Expander Plates designed to be used in 12 or 24 volt, DC or FWR (full wave systems. Amber lens strobes are UL 1638-Listed Signaling Appliances) for Private Mode General Utility A table is also provided to show the candela rating the UL 1971 test procedures. All SpectrAlert Advance are suitable for use in synchronized systems. The Sensor MDL module may be used to provide synchro- See installation document I56-3829-001R for mounting details and restrictions. UL 1638-Listed amber lens strobe included. Meets DOD specification requirements. Field-selectable candela settings: 15, 15/75, 30, 75, 95, 110, 115 (please refer to Candela Rating for UL 1971 Table). Automatic selection of 12- or 24-volt operation at 15 and 15/ candela. Compatible with System Sensor synchronization protocol. Optional tamper-resistant screw included. Designed to be used in 12 or 24 volt, DC or FWR systems. Rated from 32 to 120 (0 to 49 SEP-SPSW is compatible with and accomodates the instal- of SPSW, SPSWH, SPSW-P, SPSWV, SPSWV-P, and SEP-SW is compatible with and accomodates the installa- of SW, SWH, SW-P, and SWH-P. Used in flush-mounted and surface-mounted applications. G-240 Devices and SEP-SPSW Strobe Device Sold Separately) Temperature: 32 to 120 (0 to 49 Humidity: 10% 93% non-condensing. Flash Rate: 1 flash per second Voltage (strobes): Regulated 12VDC/FWR or regu- 24DC/FWR Voltage Range (includes fire alarm panels with in sync): 8 to 17.5V (12V nominal) or 16 to 33V (24V Voltage with MDL Sync Module: 9 to 17.5V (12V or 17 to 33V (24V nominal) terminal wire gauge: 12 to 18 AWG Plate Only: SEP-SW: 4 in x 4 in x 1.5 in single gang, double gang, 4 in SEP-SPSW: 4 in x 4 in x 2.125 in or deeper Plate with Strobe or Speaker Strobe Device: SEP-SW & SEP-SPSW: L 9.6 in (245 mm) W 5.1 in (130 D 3.7 in (94 mm) SPSEP-BBSW & SEP-BBSW: L 10.1 in (257 mm) W 5.6 in mm) D 2.5 in (64 mm) Box Skirts: SPSEP-BBSW & SEP-BBSW: 4 in x 4 in x 2.125 in Weight: SEP-SW & SEP-SPSW: 0.88 lb (0.4 kg) SPSEP-BBSW & SEP-BBSW: 0.69 lb (0.31 kg) 02/10/2012 Page 1 of 2 Current Draw Data Max. Strobe Current Draw (mA) for SEP-SW, SEP-SPSW: (Amber Strobe Only) to 17.5 V to 33 V Derating for Amber Lens Strobe Switch Rating 1638) Cd Rating for profile (UL 1971*) UL 1971 is not applicable to emergency communication devices, these readings were obtained using the measurement procedure under UL 1971. Listings and Approvals listings and approvals apply to the modules specified in document. In some cases, certain module