Fire-Lite SpectrAlert® Advance Chime_Strobes

SpectrAlert Advance Output CHR, CHW Chimes CHSR, CHSW Chime/Strobes Sensor SpectrAlert Advance selectable-output and chime/strobes are private-mode notification appli- used to alert trained personnel to investigate possible situations and to take appropriate action. Security and nurse workstations are ideal locations for chime Advance chimes and chime/strobes are rich with guaranteed to cut installation times and maximize The SpectrAlert Advance series of notification appli- is designed to simplify your installations, with features as: plug-in designs, instant feedback messages to correct installation of individual devices, and seven candela settings for chime/strobes. specifically, when installing Advance products, first a universal mounting plate to a four-inch (10.16 cm) four-inch octagonal, single-gang, or double-gang junc- box. connect the notification appliance circuit wiring to the terminals on the mounting plate. attach the chime or chime/strobe to the mounting plate inserting the product tabs in the mounting plate grooves. device will rotate into position, locking the product pins the mounting plate terminals. The device will temporarily in place with a catch until it is secured with a captive screw. Advance products allow you to choose: 12 or 24 volts. At 24 volts, 15, 15/75, 30, 75, 95, 110, or 115 candela by of rear-mounted slide-switch and front-view window. Chime tones and volume by way of rotary switch. Plug-in design. Shorting spring on mounting plate for pre-installation conti- Captive mounting screw. Torx screw for tamper resistance. Field-selectable candela settings: 15, 15/75, 30, 75, 95, Automatic selection of 12- or 24-volt operation at 15 and 15/ Minimal intrusion into the backbox. Rotary switch for tone selection. Two volume settings. Electrically compatible with existing SpectrAlert products. Specifications Advance chimes and chime/strobes shall mount to standard 4.0″ x 4.0″ x 1.5″ backbox, 4.0″ octagonal backbox, 2.0″ x 4.0″ x 1.875″ backbox, or double-gang A universal mounting plate shall be used for products. The notification appliance circuit wiring universal mounting plate. Also, Advance products, when used with at check. 115. candela. G-236 Devices (CHW) (CHSR) Module accessory, shall be powered from a notification appliance circuit output and shall on a nominal 12 or 24 volts. When used with the Module, 12-volt rated notification appliance circuit shall operate between 9 and 17.5 volts; 24-volt rated appliance circuit outputs shall operate between 17 33 volts. Indoor SpectrAlert Advance products shall between 32 and 120 from a regulated DC, or full- unfiltered power supply. Chime/strobes shall field-selectable candela settings of 15, 15/75, 30, 75, 95, and 115. COMBINATION chime/strobe shall be a System Sensor SpectrAlert Model _______ listed to UL/ULC 1638 and UL/ULC The chime/strobe shall comply with the Americans with Act requirements for visible signaling appliances, at 1 Hz over the strobe entire operating voltage The strobe light shall consist of a xenon flash tube and lens/reflector system. The chime shall have two options and an option to switch between a temporal and a non-temporal (continuous) pattern. These are set by a multiple position switch. MODULE module shall be a System Sensor Sync _______ to UL/ULC 464 and shall be approved for fire protective The module shall synchronize SpectrAlert strobes at 1 and chimes at Temporal 3. Also, while operating the the module shall silence the chimes on chime/strobe over a single pair of wires. The module shall mount to 4.688″ x 4.688″ x 2.125″ backbox. The module shall also