Fire-Lite ANN-80 Annunciator Datasheet

ANN 80 Serial LCD Annunciator ANN 80 annunciator is a compact backlit 80 character LCD annunciator that mimics the Fire Alarm Control Panel FACP It provides system status indicators for AC Power Alarm Supervisory and Alarm Silenced conditions The ANN 80 the FACP communicate over a two wire serial interface employ the ANN Bus communication format Connected devices are via two additional wires by either the host FACP or a UL listed filtered power supply The ANN 80 is red for order ANN 80 W ANN 80 displays English language text of system point informa including device type zone independent point alarm trouble or status as well as any custom alpha labels programmed the control panel It includes control switches for remote control critical system functions A keyswitch prevents unauthorized of the control switches to eight ANN 80s may be connected to the ANN Bus of each No programming is required which saves time during system Listed to UL Standard 864 9th Edition Backlit 80 character LCD display 20 characters x 4 lines Mimics all display information from the host panel Control switches for System Acknowledge Signal Silence Drill Reset Control switches can be independently enabled or disabled at the Keyswitch enables disables control switches and mechanically annunciator enclosure Keyswitch can be enabled or disabled at the FACP Enclosure supervised for tamper System status LEDs for AC Power Alarm Trouble Supervisory Alarm Silence Local sounder can be enabled or disabled at the FACP ANN 80 connects to the ANN Bus terminal on the FACP and minimal panel programming Displays device type identifiers individual point alarm trouble zone and custom alpha labels Time and date display field Surface mount directly to wall or to single double or 4 square box Semi flush mount to single double or 4 square electrical box ANN SB80KIT for angled view mounting Can be remotely located up to 6,000 feet 1,800 m from the Backlight turns off during AC loss to conserve battery power but turn back on if an alarm condition occurs May be powered by 24 VDC from the host FACP or by remote supply requires 24 VDC Up to eight ANN 80s can be connected on the ANN Bus and Indicators AC Power Alarm Trouble B 90 Supervisory Alarm Silenced Operating voltage range 18 VDC to 28 VDC Current consumption 24 VDC nominal filtered and non 40 mA maximum Ambient temperature 32 to 120 0 to 49 Relative humidity 93 2 RH non condensing at 32 5.375 13.65 cm high x 6.875 17.46 cm wide x 1.375 3.49 90 3 deep For use indoors in a dry location All connections are power limited and supervised ANN Bus THE DEVICES ON THE ANN BUS FROM AUXIL POWER SUPPLY ANN Bus can be powered by an auxiliary power supply when maximum number of ANN Bus devices exceeds the ANN Bus requirements See the FACP manual for more information DEVICE ADDRESSING ANN Bus device requires a unique address ID Number in to communicate with the FACP A maximum of 8 devices can connected to the FACP ANN Bus communication circuit See the manual for more information REQUIREMENTS COMMUNICATIONS CIRCUIT ANN 80 connects to the FACP ANN Bus communications cir To determine the type of wire and the maximum wiring distance can be used with FACP ANN Bus accessory modules it is nec to calculate the total worst case current draw for all modules a single 4 conductor bus The total worst case current draw is by adding the individual worst case currents for each For total worst case current draw on a single ANN Bus refer to FACP manual 3 15 2018 Page 1 of 2 REQUIREMENTS POWER CIRCUIT 14 to 18 AWG 0.75 2.08 mm2 wire for 24 VDC power circuit is Power wire distance limitation is set by 1.2 volt maxi line drop form source to end of circuit All connections are power limited and supervised A maximum of eight ANN 80 modules may be connected to this Options Red 80 character LCD Annunciator White 80 character LCD Annunciator Red surface mount backbox with angled wedge White surface mount backbox with angled Listings and Approvals listings and approvals below apply to the ANN 80 In some certain modules may not be listed by certain approval agen or listing may be in process Consult factory for latest listing UL S2424 FM approved CSFM 7120 0075 0211 MEA 442 06 E Alarms is a registered trademark of Honeywell International Inc by Honeywell International Inc All rights reserved Unauthorized use of this is strictly prohibited document is not intended to be used for installation purposes We try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice 2 of 2 DF 52417 D 3 15 2018 more information contact Fire Alarms Phone 800 627 3473 FAX 877 699 4105 of Origin USA