Fire-Lite CP355(A)

CP355 A Addressable Smoke Detectors CP355 A addressable low profile plug in ionization uses a state of the art ionization sensing chamber to open area protection and is used exclusively with addressable Fire Alarm Control Panels FACPs ionization detector is used to sense products of combus and report the measured level of such products to the fire control panel Since this detector is addressable it will emergency personnel quickly locate a fire during its early potentially saving precious rescue time while also property damage Two LEDs on each sensor light to a local visible sensor indication Remote LED annun capability available as an optional accessory RA100Z A loop Two wire loop connection Unit uses base for wiring Addressable by device Rotary decimal addressing 01 99 with MS 9200 MS and MS 9200UDLS C and 01 159 with MS and MS 9600UDLS Unique single source dual chamber design to respond and dependably to a broad range of fires communications and built in type identification Sleek low profile design Built in tamper resistant feature Removable cover and insect resistant screen for simple cleaning Withstands air velocities up to 1,200 feet per minute 6.1 m without triggering a false alarm Factory preset at 1.5 nominal sensitivity for panel alarm level Visible LED when the unit is addressed communi with the fire panel and latches on in alarm Sealed against back pressure Direct surface mounting or electrical box mounting Base mounts to single gang box 3.5 8.89 cm or 4.0 cm octagonal box or 4.0 10.16 cm square electri box using a plaster ring ionization detectors in life safety applications to provide a range of fire sensing capability especially fast flaming Where smoldering fires are anticipated a photoelectric may provide faster response detectors are constructed of off white plastic CP355 A low profile smoke detectors are designed to commer standards and offer an attractive appearance E 260 Devices in B210LP A Base plug in detectors use a detachable mounting base simplify installation service and maintenance base all base types on an electrical backbox which is least 1.5 3.81 cm deep For a chart of compatible junction see DF 60059 Because of the inherent supervision provided by the SLC end of line resistors are not required Wiring or are permitted for Style 4 Class B wiring CP355 A uses one of 99 possible addresses on the MS MS 9200UD and MS 9200UDLS C or up to 318 159 each loop on the MS 9600 Series Signaling Line Circuit It responds to regular polls from the system and reports type and status CP355 A addressable ionization sensor unique unipolar responds quickly and uniformly to a broad range of conditions and can withstand wind gusts up to 1,200 6.01 m sec without sending an alarm level Because of its unipolar chamber the CP355 A is two times more responsive than most ionization This makes it a more stable detector range 15 32 VDC peak current 300 24 VDC current 6.5 mA 24 VDC latched velocity 1,200 ft min 6.1 m sec maximum 2.0 51 mm high base determines diameter B210LP A 6.1 15.5 cm diameter B501 A 4.1 10.4 cm diameter B200SR A 6.875 17.46 cm diameter B224RB A 6.2 15.748 cm diameter 01 05 2012 Page 1 of 2 Test magnet with telescoping handle Detector removal tool Allows installation and or of detector heads from bases in high ceiling applica Extension pole for XR2B Comes in three 5 foot 1.524 sections Detector removal tool without pole Black detector covers box of 10 White detector covers box of 10 3.6 oz 102 g 0 to 49 32 to 120 humidity 10 93 noncondensing and Approvals and approvals below apply to the CP355 A detector some cases certain modules may not be listed by certain agencies or listing may be in process Consult fac for latest listing status UL Listed S1059 ULC Listed S1059 CSFM 7271 0075 0193 MEA 319 02 E FM approved Line Information suffix indicates ULC Listed model Addressable Same as above with ULC Listing B210LPA base detector B210LP base BASES suffix indicates ULC Listed model The detector plug in base can be changed off for special For details about intelligent bases and their mount see DF 60059 Plug in detector base included standard U S low profile mounting base Bulk pack of B210LP package contains 10 Standard European flangeless mounting base Bulk pack of B501 package contains 10 Intelligent sounder base capable of producing output with ANSI Temporal 3 or continuous tone B501BH series bases in retrofit applications Plug in System Sensor relay base Screw termi up to 14 AWG 2.0 mm Relay type Form C Rating 2.0 30 VDC resistive 0.3 A 110 VDC inductive 1.0 A VDC inductive Plug in System Sensor isolator detector base 25 devices between isolator bases See DF Retrofit flange to convert B210LP A to match the profile or to convert older high profile bases to Bulk pack of F110 package contains 15 Replacement flange for B210LP A base Remote LED annunciator 3 32 VDC Mounts to U S single gang electrical box For use with B501 A and bases only Surface mounting kit magnet Alarms is a registered trademark of Honeywell International Inc by Honeywell International Inc All rights reserved Unauthorized use this document is strictly prohibited document is not intended to be used for installation purposes We try to keep our product information up to date and accurate cannot cover all specific applications or anticipate all requirements specifications are subject to change without notice more information contact Fire Alarms Phone 800 627 3473 FAX 877 699 4105 in the U S A 2 of 2 DF 52383 B1 01 05 2012