Fire-Lite H350R Addressable Thermal Sensor

Installation and Maintenance Instructions for Plug in Model H350R of Rise Temperature Sensor with Fixed Temperature Alarm DESCRIPTION H350R is an addressable sensor that uses a state of the art thermistor sensing circuit for fast response This sen is designed to provide open area protection with 50 foot spacing capability and is intended for use with compatible panels only The sensor responds to rate of rise conditions of greater than 15 The sensor also provides temperature alarm detection at 135 LEDs on each sensor light to provide a local visible sensor indication Remote LED annunciator capability is avail as an optional accessory Part No RA400Z Temperature Humidity Range Range Current Current Temperature Setpoint of Rise Detection GUIDE inches 155 mm installed in B310LP inches 51 mm ounces 150 gm to 100 to 38 to 93 Relative Humidity Noncondensing flanged base to 32 Volts DC Peak 24 VDC one communication every 5 sec with LED blink enabled 6.5 mA 24 VDC 57 to greater than 15 to the installation instructions for the plug in base being used Bases are equipped with screw terminals for power ground remote annunciator connections See Figure 1 All wiring must conform to applicable local codes ordinances and regulations Verify that all sensor bases are installed and that the wiring polarity is correct at each base Disconnect the power from the loop before installing sensors installing sensors please thoroughly read the system wiring and installation manual which provides detailed in on sensor spacing placement zoning and special applications Copies of these manuals are available from NFPA standard 72 should also be referenced refer to insert for the Limitations of Fire Alarm Systems Statement device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device not cause harmful interference and 2 this device must accept any interference received including interference that cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in residential installation This equipment generates uses and can radiate radio frequency energy and if not in and used in accordance with the instructions may cause harmful interference to radio communications there is no guarantee that interference will not occur in a particular installation If this equipment does harmful interference to radio or television reception which can be determined by turning the equipment off on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 4 I56 037 00R Fire One Fire Place Northford CT 06472 Do not loop wire under terminals 1 or 2 Direct Heat Method Hair dryer of 1000 1500 watts wire run to provide supervision of connections From the side of the detector direct the heat toward the sensor Hold the heat source about 6 inches 15 cm away prevent damage to the cover during testing The LEDs on the detector should light when the temperature at the detector reaches the alarm setpoint If the LEDs to light check the power to the detector and the wiring in the detector base Reset the detector at the system control panel that fail these tests should be returned for repair 3 Views showing position of test magnet TEST MARKER Install Sensors 1 Verify that the sensor type matches the type written on the label in the base Set the address on the sensor per job drawings Some panels support extended addressing In order to set sensor above address 99 on compatible systems carefully the stop on the upper rotary switch with thumb or finger shown in Figure 2 Place the sensor into the sensor base Turn the sensor clockwise until it drops into place Continue turning the sensor clockwise to lock it in place Tamper Resistance sensor base includes a tamper proof feature which when activated prevents of the sensor without the use of a tool See the installation instruction for the sensor base for details in using this feature STOP 2 After all sensors have been installed apply power to the control unit Test the sensor by placing a magnet against the sensor plastic as shown in Figure 3 The alarm level should be recog at the panel and the LED controlled by communication command from the panel The reset of the sensor LED is controlled by communication command from the panel SENSITIVITY must be tested after installation and periodic maintenance The sensitivity may be tested in the following ways Test Magnet p n M02 04 01 or M02 09 00 Place the optional test magnet against the cover in the magnet test area as shown in Figure 3 to activate the test The LEDs should latch on within 10 seconds indicating alarm and annunciating the panel Reset the detector at the system control panel