Fire-Lite IPGSM-COM IP Internet and Digital Cellular Fire•Communicator

IPGSM COM Internet and Digital Cellular IPGSM COM is a compact alarm communicator panel It to the primary and secondary communication ports of Fire Alarm Control Panel DACT In the event of an off nor condition the panel sends contact ID formatted information the IPGSM COM communicator panel The IPGSM COM reformats the data into highly encrypted Ethernet packets transmission to the AlarmNet receiver via customer provided connection communication methods are critical in the market due to VoIP Voice over IP migration from POTS telephone service and growth of digital radio networks The delivers secure reliable and complementary Inter and digital communications via the GSM Global System for network Our exclusive Triple Path Communications combines Internet service with GSM for added reliability an extra level of security The GSM radio technology is in that it uses GPRS service General Packet Radio Ser for data and alarm communications and automatically to SMS Short Message Service for alarms if GPRS is Through the Internet or GSM radio the IPGSM offers contact ID reporting with any Fire Alarm Control signals from the IPGSM COM communicator panel are deliv to Honeywell AlarmNet Network Control Center which the information to the appropriate central station The of the art AlarmNet Network Control Center is fully redun and monitored 24 7 AlarmNet has the ability to route mes using AlarmNet i and 800 PLUS services providing true and multi path message delivery Saves the cost of two dedicated phone lines Only the cus shared IP equipment is required Triple path communications Uses Internet as primary with GSM technology as back up GSM path utilizes GPRS automatically switches to SMS if GPRS is unavailable Requires no change to the existing Fire Alarm Control Panel The IPGSM COM connects directly to the pri and secondary telephone ports Works over any type of customer provided Ethernet 10 network connection LAN or WAN DSL modem or modem Data transmits over standard contact ID protocol but is with the industry advanced encryption standard 256 bit Supports both dynamic DHCP or Public and Private Static addressing Built In Power Supply module On board charging circuit accommodates back up battery Includes primary and battery supervision Diagnostic LEDs Signal strength and status indications Reliable connection IP and GSM tested everyday QOS Quality of Service diagnostics via AlarmNet supply vital including when message was received battery input voltage signal strength and message path Web Based Programming or Handheld programmer for cid 129 ECN 11 0070 an event occurs the Fire Alarm Control Panel goes off to dial the central station The IPGSM COM Dialer Capture detects the off hook condition and provides the fire with a dial tone When the fire panel detects the dial tone begins dialing the central station The Dialer Capture Module the three second period after dialing as the number has been completed After the dialing is completed the Capture Module returns a handshake to the fire panel fire panel then sends the contact ID reports to the Dialer Module which in turn sends a kiss off after the report is received from the fire panel The Dialer Capture sends the contact ID reports over the ECP bus to the communications module When all the reports are sent fire panel goes on hook The iGSM communications module transmits the messages to the central station either over internet primary or the GSM network to Program are two ways to configure the IPGSM COM communica panel Handheld programmer 7720P Web Based Programming Allows complete interactive from AlarmNet Direct IPGSM COM Communicator can be pre programmed Use 7720P programmer or the Web Based Program to enter all information This is saved to the IPGSM COM panel memory When the IPGSM COM Commu is installed at the site and connected to the Internet it registers itself with the AlarmNet receiver This elimi the need for a PC at the remote site for programming most installations the only required parameters are Primary City ID two digits obtained from your monitoring Primary Central Station ID two digits obtained from your station 02 23 2011 Page 1 of 2 Specifications Dimensions 14.875 H x 12.75 W x 3.0 D 37.8 cm H x cm W x 7.6 cm D Color Red Specifications Weight 5.3 lbs 6.94 kg Dimensions 15.625 H x 13.79 W x 9.25 D 39.7 cm H x cm W x 23.9 cm D and Humidity Ranges system meets NFPA requirements for operation at 0 120 and at a relative humidity 93 2 RH non at 32 2 90 3 However the useful of the system standby batteries and the electronic compo may be adversely affected by extreme temperature and humidity Therefore it is recommended that this and its peripherals be installed in an environment with a room temperature of 15 27 80 Line Information Internet and Digital Cellular Fire Communicator Includes red cabinet with key wall outlet box Dialer Cap Module iGSM Communications Module antenna and adapter PowerBoost1 power supply LED display transformer manual and required screws cables etc 3db gain external remote antenna 50 ft antenna cable low loss 25 ft antenna cable low loss SNA to N Adapter IPGSM COM handheld programmer Plug in transformer box for IPGSM communicator Battery 12 Volts 7 AH sealed Listings and Approvals listings and approvals below apply to the basic IPGSM communicator panel In some cases certain modules may be listed by certain approval agencies or listing may be in Consult factory for latest listing status UL S789 CSFM 7300 1645 0183 Primary Subscriber ID four digits obtained from your moni station Communication Module MAC ID and MAC CRC number on outside of box and inside of the module of these parameters are assigned by the monitoring station IPGSM COM Installation and Setup Guide for full details Some assembly is required Capabilities IPGSM COM communicator panel is compatible with fire that use the Contact ID communications format as in the SIA DC 05 standard AlarmNet has been the nationwide leader in alarm technology since 1986 A reliable alternative the transmission of alarm signals our radio network provides coverage in the United States and Canada Network Control center processes signals from pow servers in multiple locations equipped with 24 7 infrastruc support The AlarmNet network consist of redundant servers hot back up databases and generators with back up at all locations to ensure continuity of service from AlarmNet are transmitted to the central station using multiple communications paths consisting of the radio network or toll free POTS service Requirements COMPLIANCE meet UL864 NFPA compliance ensure the following must be mounted within the same room and 20 feet of host Fire Alarm Control Panel sounder or remote sounder must be powered from the same un switched power source branch as the host Fire Alarm Control must use the 7AH battery to provide 24 hour capability Specifications Transformer Primary 120 VAC 60 Hz 0.50 A Secondary 18VDC 50 VA Current Requirements PowerBoost1 power supply 90mA Standby 90 mA Active iGSM Communications Module 80mA Standby 500mA peak during transmission Dialer Capture Module 40mA Standby 85mA Active LED Display board 10mA Standby 10mA Active TOTAL 220mA Standby 685mA Active Battery One 12 V 7.0 AH lead acid battery not supplied