Fire-Lite LDM Lamp Driver Module

May 12 1998 Series Driver Modules Annunciators Fire 2000 2000 LDM Series Lamp Driver Modules when combined with a cus graphic display provide annunciation and control for the 2000 and MicroScan 9200 fire alarm control panels modules use a serial communications interface and may be up to 6,000 feet from the panel ALARM CIRCUIT ON and TROUBLE lamp LED per point option more dense alarm only option field selectable Control switch option for remote control per point Lamps LEDs may be programmed to display status of notification or control relays as well as system status conditions System trouble lamp LED signal On line power LED indicator Alarm and trouble resound with flash of new conditions Local sounder for both alarm circuit on and trouble conditions with switch connection Serial EIA 485 interface for reduced installation cost May be powered by 24 VDC from the panel or by remote power Efficient switched power converter reduces power consumption Microprocessor controlled electronics fully supervised Plug in terminal blocks for ease of installation and service Trouble monitor option for remote power supplies basic models are available the LDM 32F control module and LDM E32F expander module Each may be selected to provide alarm indications or 16 alarm 16 trouble and 16 control points LDM 32F LDM E32F with a custom graphic array may be used indicate point status and in some versions to control the state of points LDM 32F and LDM E32F modules mount on four standoffs in the custom annunciator graphic box Alternately the modules be installed in a standard CHS 4 chassis Sensiscan 2000 or in an ABS 8RF backbox when used with the MS 9200 module size is approximately 4.4 11.2 cm x 7.1 18 cm between the LDM Series annunciators and the host Alarm Control Panel are made through a two wire EIA 485 multi loop and a two wire regulated 24 VDC power loop Up to 32 systems may be connected to a single control panel field wiring terminations use removable compression type ter blocks for ease of installation wiring and circuit testing document is not intended to be used for installation purposes We try to keep our information up to date and accurate We cannot cover all specific applications or all requirements All specifications are subject to change without notice For information contact Fire cid 149 Lite Phone 203 484 7161 FAX 203 484 7118 Clintonville Road Northford Connecticut 06472 and Manufacturing System Certified to Standard ISO 9001 in the U S A cid 151 Page 1 of 2 Series Lamp Driver Modules are used to provide the Fire cid 149 Lite Sensiscan 2000 MicroScan 9200 with an interface to a custom graphic annunciator or remote power supplies and serial communications allow the custom annun to be located virtually anywhere on the protected premises system alarm and or trouble conditions may be annunciated on a per point or in a grouped zone configuration of system operational controls such as Signal Silence System Reset and annunciation controls such as Local Acknowledge and Lamp Test may be through special key or push switches LINE INFORMATION Lamp Driver Module with 32 alarm lamp driver transistors sink to power on alarm May be selected dip switch for 16 alarm circuit on 16 trouble 16 switch inputs if desired Also includes system trouble lamp driver and lamp switch input Integral piezo sounder sounds for each new or trouble and is silenced with the Local Acknowledge switch or permanently with a dip switch selection Flash of new alarms or troubles is selectable dip switches 16 switch inputs may be used for panel SILENCE RESET ACKNOWLEDGE or remote output control NACs and relays Sensiscan 2000 Instructions are included Lamp Driver Module with 32 alarm drivers or 16 alarm 16 trouble 16 switch inputs One LDM E32F is allowed per LDM 32F in alarm only mode LDM E32F modules are allowed per LDM 32F in alarm trouble Includes ex ribbon cable cid 150 LDM CBL24 LDM CBL48 Ribbon cable sets to provide either a 60.96 cm or 48 121.96 cm connection between LDM 32F LDM E32F and LEDs lamps on a custom graphic panel Includes all cables necessary for one LDM 32F LDM E32F Cables have connector on one end only split strip and connect other to graphic annunciator specifications on LDM Graphic Annunciator Lamp Driver Modules contact Fire cid 149 Lite 2 of 2 cid 151 DF 51384