Fire-Lite PA400 Sounder-Strobe

GENERAL Sensor cid 146 s model PA400 Mini Alert Sounder is com and reliable PA400 the Mini Alert piezo horn has a 90 dBA sound output and operates at 12 and 24 VDC and wave rectified unfiltered This compact device is ideal hotel motel or residential fire system applications aesthetics demand a small indicating device UL 1638 compliant PS Series signal strobe is an elec visible warning signal that flashes approximately once 1.5 seconds Available in a 1.5 cd light intensity the light uses an extremely reliable xenon flash tube low current requirements The electronic circuit is en within the durable polycarbonate lens All circuits polarized to be compatible with DC alarm supervision satisfy the latest code requirements for primary visible add on strobes field install to the PA400 Series but are listed for secondary visible signaling only Attractive styling ideal for residential or hotel applica Polarized for DC supervision Interrupted tone 90 dBA output at 10 feet 3 meters 1.5 candela add on strobe secondary signaling Operates from 10 to 32 VDC Low current drain Easy field wiring with SEMS screws Available in red beige or white Mounts in standard single gang backbox Three year warranty AND OPERATION sounder operates electronically and uses the piezo The sounder is mounted on a wall plate which is in red white or beige Optional strobes models and PS24LO are easily mounted to sounders in field The red colored sounder is intended for use in alarm indicating circuit of a UL listed 12 or 24 VDC fire control panel Optional strobe additions of the PA400 PS12LO and PS24LO require a 12 or 24 VDC respectively These devices are available in dual red or beige PA400 is available in white and in several different configurations 16 1998 Sounder Optional Strobe Audio Visual Devices PA400 PSLO PA only Fire PA400 Optional Strobe PA400 sounder is designed for fire alarm and security haz warning Optional strobe is recommended to protect hearing impaired and anyone occupying noisy areas National Fire Protection Association publishes codes and recommended practices for the installation use of sounders and strobes document is not intended to be used for installation purposes We try to keep our information up to date and accurate We cannot cover all specific applications or all requirements All specifications are subject to change without notice For information contact Fire cid 149 Lite Phone 203 484 7161 FAX 203 484 7118 Clintonville Road Northford Connecticut 06472 and Manufacturing System Certified to Standard ISO 9001 in the U S A cid 151 Page 1 of 2 Sounder Strobe AWG 12 3.25 mm to 18 0.75 mm Di without strobe 4 9 16 cid 148 115.89 mm high x 2 71.44 mm wide x 1 1 8 cid 148 28.58 mm deep di with strobe 4 9 16 cid 148 115.89 mm high x 2 13 71.44 mm wide x 2 cid 148 50.8 mm deep Weight with strobe 2.4 oz 68 g weight with strobe 5.6 oz g Mounting 2 1 2 cid 148 63.5 mm single gang backbox temperature range 14 cid 176 F to 140 cid 176 F 10 cid 176 C to voltage 12 and 24 VDC and full wave recti unfiltered Actual 12 volt operating voltage cannot be than 9.6 VDC or greater than 15.4 VDC actual 24 volt voltage cannot be less than 18 VDC or greater 33 VDC All models can be powered using full wave recti unfiltered supplies Under no circumstances can MA SS12 24 or PA400 series devices input voltage 33 VDC or be less than 9.6 VDC instructions are packaged with each unit The is intended for mounting to a standard 2 1 2 deep box which allows sufficient clearance for con entrance The PA400 is compatible with DC line su The piezo sounder is polarized and has termi marked with polarity Apply positive supply voltage to terminal and negative supply voltage to the terminal wiring diagram Mount the appliance to the electrical box using the two mounting screws supplied Wiring be in compliance with all codes and must not be of length or wire size which would cause the appliance operate outside of its published specifications National Fire Protection Association has published standards and recommended practices for the in and use of sounders and strobes It is recom that the installer be familiar with these require with local codes and any special requirements of Local Authority Having Jurisdiction SPECIFICATIONS shall be a System Sensor Model ca of operating at 12 and 24 VDC Sounder shall be to Underwriter cid 146 s Laboratories Standard 464 for fire signaling systems Sounder shall have an op temperature between 14 cid 176 F and 140 cid 176 F 10 cid 176 C to Sounder shall have eight tone options selected by of clip s sounder strobe combination shall be a System Sensor Sounder Strobe capable of operating at 12 or 24 VDC shall be listed to Underwriters cid 146 Laborato Standard 464 1638 for fire protection signaling sys Sounder strobe shall have an operating temperature 14 cid 176 F and 140 cid 176 F 10 cid 176 C to 60 cid 176 C Strobe shall a minimum light output of 1.5 or 15 candela and shall UL listed as a secondary signaling device Shown with control panel alarm Panel polarity reversed supervisory condition LINE INFORMATION 2 of 2 cid 151 DF 50727