Fire-Lite PCPS24F Power Supply

June 23 1998 Volt 6 Amp Remote Power Supply Power Supplies Accessories Fire Fire cid 149 Lite FCPS 24F E is a compact cost effective remote power supply with battery charger The may be connected to any 12 or 24 volt Fire Control Panel FACP or may stand alone Primary include Notification Appliance bell Circuit expansion to support ADA requirements or auxil power to support 24 volt system accessories The provides regulated and filtered 24 VDC power to four Appliance Circuits two Class A Style Z and Class B Style Y or four Class B only Alternately the outputs may be configured as any combination of re power outputs optimal for power four wire smoke detectors The FCPS 24F E also con a battery charger capable of charging up to 7.0 Amp batteries Requires input trigger voltage of 9.0 32 VDC Contains two fully isolated input control circuits trig from FACP Notification Appliance Circuit NAC mode or jumpered permanently on stand mode Two Class A Style Z or Class B Style Y Notification Circuits circuits 1 3 Two additional NACs that may be individually configured Class B Style Y operation only circuits 2 4 6 Amp full load output 3 amps max ckt in NAC ex mode UL 864 4 Amp continuous output in stand alone mode UL 1481 In stand alone mode output power circuits may be con as resettable reset line from FACP required or Fully regulated and filtered power output optimal for four wire smoke detectors annunciators and system peripherals requiring regulated filtered Fuseless power limited technology meets new UL power requirements effective May 1 1995 Normally closed trouble contact Fully supervised power supply battery and Notification Circuits Selectable earth fault detection AC trouble report selectable for immediate 8 or 16 hour Self contained in compact lockable cabinet 15 381 H x 14.5 368 mm W x 2.75 70 mm D Includes integral battery charger capable of charging up Fixed clamp type terminal blocks accommodate up to 12 7.0 AH batteries 3.25 mm wire and CODES FCPS 24F complies with the following standards NFPA 72 1996 National Fire Alarm Code UL 864 Standard for Control Units for Fire Alarm Systems UL 1481 Power Supplies for Fire Alarm Systems Optional ammeter voltmeter Works with virtually any UL 864 fire alarm control which an industry standard reverse polarity notification expander mode mode document is not intended to be used for installation purposes We try to keep our information up to date and accurate We cannot cover all specific applications or all requirements All specifications are subject to change without notice For information contact Fire cid 149 Lite Phone 203 484 7161 FAX 203 484 7118 Clintonville Road Northford Connecticut 06472 and Manufacturing System Certified to Standard ISO 9001 in the U S A cid 151 Page 1 of 3 AC Power FCPS 24F 120 VAC 50 60 Hz 2.0 A max FCPS 24FE 220 240 VAC 50 60 Hz 1.0 A max Wire size minimum 14 AWG 2.0 mm with 600V Input Circuit Trigger Input Voltage 9.0 to 32 VDC mA 16 32 V Trigger Current mA 9 16 V input Contact Rating 5 amps at 24 VDC DESIGNATIONS Power Output Specific Application Power 45 mA Short Circuit Circuits 24 VDC 19.1 26.4 filtered regulated 3.0 amps maximum for any one circuit 4.0 amps maximum total continuous current for all out Stand alone mode 6.0 amps maximum total short term current for all outputs Expander mode Power Battery Charging Circuit Supports lead acid batteries only Float Charge Voltage 27.6V Maximum Charge Current 250 mA Maximum Battery Capacity 7.0 AH Cut JP1 to use a UL listed external charger or MPM 4F ammeter Cut R134 to delay AC loss report for 8 hours 24 hour standby or R134 and R76 to delay AC loss 16 hours 60 hour standby Cut R175 to make output 2 non in stand alone mode Cut R176 to make output 4 non in stand alone mode INFORMATION charger power supply 120 VAC main printed circuit board red enclosure and instructions charger power supply 220 240 Includes main printed circuit transformers red enclosure and instructions 2 of 3 cid 151 DF 51401 VDC end of line relay for 4 wire smoke detector power 12 volt 7.0 AH two required ammeter voltmeter Mounts in backbox EXAMPLES 1.0 Expand notification appliance power an additional 6.0 amps Use up to 4 Class B Style Y or 2 Class A Style Z and 2 Class B Style Y outputs this example the FACP notification appliance circuits will activate the FCPS 24F E when reverse polarity occurs Trouble conditions on the FCPS 24F E are sensed by the FACP through Notification Appli Circuit 1 2.0 Use the FCPS 24F E to expand auxiliary regulated 24 volt system power up to 4 amps non resettable and resettable power options are available outputs are created by connecting the resettable output from the FACP to one or both of the FCPS inputs Non resettable outputs are created simply by cutting on board resistors For addressable panel use a monitor module to sense the trouble status of the FCPS 24F E via the trouble relay contacts 3.0 Use addressable control modules to activate the FCPS 24F E versus the FACP Notification Circuits This typically allows for mounting the FCPS 24F E at greater distances from the FACP while expanding system architecture in various applications this example an addressable control module is used to activate the FCPS 24F E and an addressable monitor is used to sense FCPS 24F E trouble conditions Local auxiliary power output from the FCPS 24F E power to the addressable control module Fire cid 149 Lite MS 9200 198 point Addressable FACP has the capability of locating control and monitor modules to 10,000 feet away cid 151 Page 3 of 3