Fire-Lite Sensican 200C Fire Alarm Control Panel

May 19 1998 200 Alarm Control Panel Conventional Fire Sensiscan 200 Fire Alarm Control Panel is a medium size unit designed for maximum flex and ease of installation The microprocessor control modular construction enable users to configure the to meet their precise requirements Field pro simplifies initial installation and allows quick to meet future needs center of the system is the Central Processor Unit module which monitors and controls one or additional user selected modules The Sensiscan 200 be configured as a 4 8 12 or 16 zone system communications are accomplished over a high serial data bus Each module on the bus is auto addressed supervised and controlled by the Medium conventional system capacity up to 16 Style B Style D Class B or A Initiating Device Circuits IDCs IDCs may be expanded in increments of 4 or 8 utilizing or IZ 8F modules Dual Style Y or Style Z Class B or A Notification Circuits NACs standard NACs may be expanded in increments of 4 or 8 utilizing modules or a combination of IC 4F and ICE 4F Integral power supply with ground fault detection battery and charging capability for 7.0 to 17.0 AH Note For batteries greater than 12.0 AH use BB 17F battery box cm center wall studs Field programmable with separate access for initial sys programming and system program changes Multiple passwords and a special programming key are to ensure the integrity of field program information Each initiating zone may be programmed for normal or supervisory operation Walk Test feature for single person test of the system special zone change audible indication and trouble indication Alarm verification programmable per zone with auto discrimination between smoke detectors and dry initiating devices Small size permits semi flush mounting between 16 Two stage Alert Evacuation option meets Canadian and Multiple hazard releasing option Four 4 cross zone per module requirements Pre signal capability with selectable time delays and Alarm Sequence PAS per latest NFPA 72 Initiating zones may be programmed to function as re Acknowledge Silence or Reset inputs Field programmable supervisory complies with NFPA requiring distinction between supervisory con and open circuit trouble conditions March time or temporal code selectable per output Map any output circuit to any input circuit in non volatile memory Releasing service capability with selectable time delays All initiating and notification appliance circuits are power circuit and manual release to meet the latest UL requirements document is not intended to be used for installation purposes We try to keep our information up to date and accurate We cannot cover all specific applications or all requirements All specifications are subject to change without notice For information contact Fire cid 127 Lite Phone 203 484 7161 FAX 203 484 7118 Clintonville Road Northford Connecticut 06472 and Manufacturing System Certified to Standard ISO 9001 in the U S A Page 1 of 4 Enable Disable of circuits from the front panel switches Silence inhibit timer option with selectable times Auto Silence option alarm cutout with selectable times Non alarm selection for lower priority monitor and control non fire signals Resound of subsequent alarms troubles or supervisory each with a distinct local audible indication Alarm and trouble reminder option ALARM red and TROUBLE yellow LEDs indicate of each initiating device circuit ON green and TROUBLE yellow LEDs indicate status notification and control circuits EIA 485 serial port for high speed data communication remote annunciators May be used for remote SIGNAL SILENCE and SYSTEM RE Labels may be easily inserted to provide identification of circuits Non volatile memory retains program information even total loss of power Automatic memory checks verify Optional auxiliary power supply available to provide power for notification appliances Extensive transient protection APPROVALS the first page of this catalog sheet for listing agencies file numbers These listings and approvals apply to basic Sensiscan 200 control panel In some cases modules may not be listed by certain approval agen or listing may be pending Consult factory for latest status Sensiscan 200 complies with the following standards NFPA 72 1993 National Fire Alarm Code Local Remote Station and Proprietary Fire Alarm UL 864 Standard for Control Units for Fire Protective Systems CAN ULC S527 M87 Standard for Control Units for Protective Signaling Systems CONFIGURATIONS following are minimum quantities of modules required configure complete 4 8 12 or 16 zone controls or IZ 4AF CR 4F or TC 4F or ICR 4L Reduce to 1 if an expander ICE 4F IZE AF or or AVPS 24F is employed Reduce to 0 when an expander and an AVPS 24F are employed 2 of 4 DF 51050 LINE INFORMATION Basic Equipment for Sensiscan Includes CPU 200 MPS 24BF power power transformer program key labels basic cables manual and hardware The CPU 200 in two 2 notification appliance circuits alarm and trouble relays remote sta and master box transmitters The CPU with up to two modules any of IZ IC CR and TC Note If an IC or TC module is installed only one IZ 4 or 8 zones may be installed Initiating Zone module provides 8 Style B Class B initiating device zones Plug in terminal blocks are for ease of installation and service Same as IZ 8F with four 4 supervisory Initiating Device Circuits points 5 8 Required for Cana Supervisory Service Same as IZ 8F with eight 8 supervisory Initiating Device Circuits points 1 8 Required for Cana Supervisory Service Initiating Zone Expander converts to eight 8 Style D Class A initiating circuits maximum of one per IZ 8F terminal blocks are included for ease installation and service Initiating Zone module Provides 4 Style B Class B initiating device Note Will not accept an IZE AF Same as IZ 4F but with four 4 D Class A zones Indicating Notification Appliance module Provides four 4 Style Y or Z Class B or A notification appliance Maximum signaling current is 3.0 per circuit or 6.0 amps per module to power supply limitations includes bell power harness and ELRs terminal blocks Indicating Notification Appliance Expander expands IC 4F to provide total of eight 8 Style Y or Style Z NACs ratings are same as IC 4F maximum one per IC 4F Plug in terminal blocks Control Relay module provides 4 Form C relay contacts rated at 5.0 120 VAC or 28 VDC resistive per cir Plug in terminal blocks Control Relay Expander expands to provide a total of eight 8 Form C contacts maximum of one per CR 4F also be connected to add four 4 re to an IC 4F TC 2F or TC 4F Plug in block Time Control module used for release and pre signal alert applications Release mode in cross zone abort circuit two 2 circuits warning bell circuit with option and countdown time dis Presignal option includes program timer Plug in terminal blocks Time Control module used for mul releasing service or two stage Release mode provides 4 independent release circuits each programmable cross zone delay timer soak timer Two stage alert evacuate provides four