System Sensor L-Series Chimes and Chime Strobes

Selectable Output and Chime Sensor L Series selectable output chimes and are rich with features guaranteed to cut times and maximize profits with lower current and modern aesthetics Updated modern aesthetics Plug in design with minimal intrusion into the back box Mounting plate shorting spring feature checks wiring continuity device installation Captive mounting screw Tamper resistant construction Field selectable candela settings Wall 15 30 75 95 110 135 185 Ceiling 15 30 75 95 115 150 177 Automatic selection of 12 or 24 volt operation 15 and 30 candela Rotary switch for tone and volume selections Five selectable tones with high and low volume settings Electrically compatible with legacy SpectrAlert and SpectrAlert Advance devices Wall models listed for wall mounting only ceiling models listed for ceiling mounting only System Sensor L Series product line of wall and ceiling chimes and chime strobes include a variety of features that their application versatility while simplifying the installation white and red plastic housings System Sensor L Series can virtually any application requirement chimes and chime strobes are private mode appliances used to alert trained personnel to investigate emergency situations and to take appropriate action guard and nurse workstations are ideal locations for products devices feature plug in design with minimal intrusion into the box making the installation fast and foolproof while virtually costly and time consuming ground faults can easily adapt devices to a wide range of application using field selectable candela settings automatic of 12 or 24 volt operation and a rotary switch for chime and two volume selections Listings 3057072 Specifications Specifications Sensor L Series chimes and chime strobes shall mount to a standard 4 4 1 back box 4 inch octagon back box single 2 4 17 8 inch back box or double gang back box A universal mounting plate shall be used for mounting products The notification circuit wiring shall terminate at the universal mounting plate Also System Sensor L Series products when used with the Module accessory shall be powered from a non coded notification appliance circuit output and shall operate on a nominal 12 or volts When used with the Sync Module 12 volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts rated notification appliance circuit outputs shall operate between 16.5 and 33 volts Indoor L Series products shall operate between and 120 degrees Fahrenheit from a regulated DC or full wave rectified unfiltered power supply Chime strobes shall have field selectable settings of 15 30 75 95 110 135 and 185 for wall units and 15 30 75 95 115 150 and 177 for ceiling units Strobe Combination chime strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1638 and UL 464 The chime strobe shall comply the Americans with Disabilities Act requirements for visible signaling appliances flashing at 1Hz over the strobe entire operating voltage The strobe light shall consist of a xenon flash tube and associated lens reflector system The chime shall have two audibility options an option to switch between temporal three pattern non temporal continuous pattern 1 second chime pattern 1 4 second chime 5 second whoop chime pattern These options are set by a multiple position switch Module module shall be a System Sensor Sync listed to UL 464 and shall be approved for fire protective service The module shall SpectrAlert strobes at 1Hz and all available chime tones Also while operating the strobes the module shall silence the chimes chime strobe models over a single pair of wires The module shall mount to a 4 11 16 4 11 16 2 1 8 inch back box The module shall also two Style Y class B circuits or one Style Z class A circuit The module shall synchronize multiple zones Daisy chaining two or more modules together will synchronize all the zones they control The module shall not operate on a coded power supply Specifications Operating Temperature Range Flash Rate Voltage Voltage Range2 Voltage Range with MLD3 terminal wire gauge strobe dimensions including lens dimensions Chime strobe dimensions including lens red wall surface mount back box white wall surface mount back box red ceiling surface mount back box white ceiling surface mount back box Full Wave Rectified FWR voltage is a non filtered time varying power source that is used on some power supply and panel outputs CHS products will operate at 12 V nominal only for 15 and 30 cd to 120 0 to 49 to 93 non condensing flash per second 12VDC or regulated 24DC FWR1 to 17.5V 12V nominal or 16 to 33V 24V nominal to 17.5V 12V nominal or 16.5 to 33V 24V nominal to 18 AWG in L 4.7 in W 1.91 in D 143 mm L 119 mm W 49 mm D in L 4.7 in W 1.25 in D 143 mm L 119 mm W 32 mm D Dia x 2.47 D 173.5mm Dia x 62.7mm D in L 4.7 in W 4.3 in D 142 mm L 119 mm W 109 mm D in L 4.7 in W 4.3 in D 142 mm L 119 mm W 109 mm D Dia x 2.5 D 175.8mm Dia x 63.5mm Dia x 2.5 D 175.8mm Dia x 63.5mm Current Draw Data Max Chime Current Draw mA RMS Pattern Second Chime High Second Chime Second Chime High Second Chime Low Chime Chime Second Whoop High Second Whoop Low Volts Volts data represents coding at 3 chimes per second Actual current draw will vary depending upon coding selected Max Chime Strobe Current Draw mA RMS Wall Max Chime Strobe Current Draw mA RMS Ceiling Input Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Input Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Input Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Volts Volts Volts Volts Volts Volts Input Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Selection tone selection is accomplished by using the rotary switch on the back of the product current draw and sound measurements for various chime tone settings are listed below Patterns chime only Rate Second Chime Second Chime Second Chime Second Chime Chime Chime Second Whoop Second Whoop Level and Chime Strobe Output dBA Sound Pattern Second Chi