System Sensor M500DM

inStAllAtion And MAintenAnCe inStruCtionS Ohio Avenue St Charles Illinois 60174 FAX 630 377 6495 dual Monitor Module Operating Voltage Current Draw Operating Current Resistance IDC wiring resistance IDC Voltage IDC Current Range to 32 VDC mA LED on LED flashing Ohms Ohms Volts to 120 0 to 49 to 93 Non condensing in H x 4 in W x 11 4 in D Mounts to a 4 inch square by 21 8 inch deep box Electrical Box inStAlling information is included as a quick reference installation guide Refer to control panel installation manual for detailed system information If the will be installed in an existing operational system inform the opera and local authority that the system will be temporarily out of service Dis power to the control panel before installing the modules This manual should be left with the owner user of this equipment deSCription Dual Monitor Module is intended for use in intelligent two wire systems provides two independent 2 wire initiating device circuits IDC at two sep consecutive addresses It is capable of monitoring normally open con fire alarm and supervisory devices or either normally open or normally security devices The module has a single panel controlled red LED requireMentS ensure proper operation these modules shall be connected to listed com system control panels only 1 ControlS And indiCAtorS directly to 4 inch square electrical boxes see Figure 2A The box have a minimum depth of 21 8 inches Surface mounted electrical boxes are available from System Sensor 2A Module Mounting 2B 6 7 8 9 All wiring must conform to applicable local codes ordinances and This module is intended for power limited wiring only Install module wiring in accordance with the job drawings and appropri wiring diagrams Set the address on the module per job drawings NOTE Monitor module L using terminals 6 and 7 responds at the ad set on the code switches Monitor module H using terminals 8 and will automatically respond at the next higher address For example if code switches are set to 76 module L will respond at address 76 and H will respond at address 77 Use caution to avoid duplicate ad of modules on the system Secure module to electrical box supplied by installer as shown in Fig 2A 3 typiCAl 2 Wire initiAting CirCuit ConFigurAtion nFpA Style B INITIATING DEVICE CIRCUITS L H EACH LIMITED TO 240 11.7 VDC MAX 47k EOL 47k EOL 6 7 8 9 NEXT PANEL OR DEVICE MODULES TO LISTED CONTROL PANELS ONLY LINE CIRCUIT SLC VDC MAX SHIELDED TWISTED IS RECOMMENDED WIRING SHOWN IS AND POWER LIMITED LISTED CONTACT CLOSURE DEVICES MAY USED DO NOT MIX FIRE ALARM INITIATING OR SECURITY DEVICES ON THE INITIATING DEVICE CIRCUIT CONTACT CLOSURE DEVICES PER INSTALLATION INSTRUCTIONS A TERMINALS 6 7 RESPONDS AT ADDRESS ON CODE SWITCHES MONITOR B TERMINALS 8 9 AT NEXT HIGHER ADDRESS liMited WArrAnty Sensor warrants its enclosed product to be free from defects in materials and under normal use and service for a period of three years from date of System Sensor makes no other express warranty for the enclosed product agent representative dealer or employee of the Company has the authority to in or alter the obligations or limitations of this Warranty The Company obligation this Warranty shall be limited to the replacement of any part of the product which found to be defective in materials or workmanship under normal use and service the three year period commencing with the date of manufacture After phoning Sensor toll free number 800 SENSOR2 736 7672 for a Return Authorization send defective units postage prepaid to System Sensor Returns Department RA 3825 Ohio Avenue St Charles IL 60174 Please include a note describing malfunction and suspected cause of failure The Company shall not be obligated to units which are found to be defective because of damage unreasonable use or alterations occurring after the date of manufacture In no case shall the be liable for any consequential or incidental damages for breach of this or any Warranty expressed or implied whatsoever even if the loss or damage is caused by Company negligence or fault Some states do not allow the exclusion or limitation of or consequential damages so the above limitation or exclusion may not apply you This Warranty gives you specific legal rights and you may also have other rights vary from state to state equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable against harmful interference This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications Operation is subject to the following two conditions 1 This device may not cause harmful radiation and 2 this must accept any interference received including interference that may cause undesired operation System Sensor StAteMent