Gamewell-FCI ATD-L2 Thermal Detector

Building Intelligent Networks FCI Series intelligent plug in thermal with integral communication features that surpass conventional Detector sensitivity can be in the control panel software is continuously monitored and to the panel Point ID capability each detector address to be set with address switches providing exact locations for selective maintenance chamber contamination reaches an level ATD Series thermal use an innovative thermistor circuit to produce 135 fixed ATD L2 and rate of rise detection ATD RL2 in a low profile The ATD HL2 provides fixed high detection at 190 These detectors provide cost effective property protection in a variety of plug in detectors use a separate to simplify installation service and main A special tool allows maintenance to plug in and remove detectors using a ladder base on a box which is at least 1.5 cm deep Suitable mounting base boxes 4.0 10.16 cm square box 3.5 8.89 cm or 4.0 10.16 cm octago box box With B501BH base use a 4.0 10.16 cm With B224RB or B224BI base use a 3.5 cm octagonal box or a 4.0 10.16 octagonal or square box Because of the inherent supervision by the SLC loop end of line resistors not required Wiring T taps or branches are for Style 4 Class wiring Sleek low profile stylish design State of the art thermistor technology fast response Rate of rise model ATD RL2 8.3 per minute Factory preset at 135 57 high model ATD HL2 at 190 Addressable by device Rotary 01 99 address switches Two wire loop connection Visible LEDs every time the is polled 360 viewing angle of the visual indicators Two red LEDs LEDs in Normal condition and turn on in Alarm Integral communications and built in identification Remote test feature from the panel Built in functional test switch activated external magnet Low standby current Listed to UL 521 Built in tamper resistant feature Designed for direct surface or mounting Sealed against back pressure Plugs into separate base for ease of and maintenance Separate allows interchange of photoelec ionization and thermal sensors SEMS screws for wiring of the 94 5V plastic flammability rating Remote LED output connection to RA400Z remote LED Optional sounder relay and isolator Single gang box except relay or isolator base ADDRESSABLE DETECTOR ISO 9001 Company pecifications are provided for information only and are intended to be used for installation purposes and are to be accurate However no responsibility is by Fire Control Instruments for their use subject to change without notice 2003 All Rights Reserve d Honeywell Company Intelligent Networks 2.1 5.1 cm high x 4.1 10.4 cm diameter installed in B501 base 6.1 15.5 cm diameter installed in ADB FL base weight 4.8 oz 137 g temperature range ATD L2 ATD RL2 to 38 to 100 ATD HL2 to 66 to spacing UL approved for 50 ft 15.24 m center to center FM approved for 25 x 25 ft 7.62 x 7.62 m spacing humidity 10 93 noncondensing ratings fixed temperature setpoint 135 57 rate of rise detection 15 8.3 per minute high temperature 190 88 SPECIFICATIONS range 15 32 volts DC peak current max avg 200 24 VDC without communication 300 24 VDC one communication every seconds with LED enabled current max 6.5 mA 24 VDC range 15 32 volts DC peak AVAILABLE 6.1 15.5 cm diameter 4.1 10.4 cm diameter or B501BHT Sounder base assembly B501BHT produces a Temporal Pattern Includes B501 base Relay Base Screw terminals up to 14 AWG 2.0 mm Relay type Form C Rating 2.0 A 30 VDC resistive A 110 VDC inductive 1.0 A 30 VDC inductive Dimensions 6.2 15.748 cm x 1.2 3.048 cm Isolator Base Dimensions 6.2 15.748 cm x 1.2 3.048 cm Maximum 25 devices between isolator bases are provided for information only and are not intended to be used for installation purposes and are believed to be accurate no responsibility is assumed by Fire Control Instruments for their use Specifications subject to change without notice 2003 All Rights Reserved Southwest Park Westwood MA 02090 USA cid 127 Tel 781 471 3000 cid 127 Fax 781 471 3099 cid 127 www firecontrolinstruments com Honeywell Company 1.0 Page 2 of 2 CONTROL INSTRUMENTS