Gamewell-FCI INI-7100, Network Interface Module FCI 7100 Series

7100 Series Network Module Series Peer to peer token ring regenerative network operat at 625K baud Up to 64 INI 7100 modules in one network Supports Versions using either copper wire INI 7100 or both copper wire and fiber optic cable Each INI 7100 regenerates the signal to extend the net up to another 3,000 feet 914.4 m wire or fiber segment 8 dB loss max Built in isolation provides for Style 4 or Style 7 wiring Network can be configured into regions for maximum non polarized network connections Mounts inside the 7100 Series control panel cabinets 255 02 E US LISTED R INI 7100 Intelligent Network Interface module pro a system that allows you to create a powerful and reliable peer to peer token ring regenerative net of up to 64 7100 series fire alarm control panels The can be configured as Style 4 6 or 7 Two versions the INI 7100 are available INI 7100 UTP is a cost effective unit that uses con 16 or 18 AWG twisted non shielded copper wire connect between two nodes Distances between nodes be up to 3,000 feet 914.4 m Each INI 7100 UTP the signal to extend the network another feet 914.4 m See wiring specifications for details INI 7100 FO provides connections to fiber optic cable type ST connectors as well as retaining the ability to conventional copper wire It can use stan fiber optic cable up to 200 microns multi mode but is for 62.5 125 microns Signal attenuation can be to 8 dB between nodes Fiber optic cable provides a with the highest degree of reliability and survivabil impervious to transients noise or ground faults It is for applications where the network must be run over distances or between structures Features INI 7100 is mounted inside the 7100 panel and is con to the 7100 Basic System Module with the included cable A DIP switch on the INI 7100 module is used set the address that the INI 7100 unit will occupy on the The network communication protocol is based token passing technology and operates at 625K 7100 series fire alarm control panel retains all the of a standard 7100 panel providing two signaling circuits supporting up to 396 amps GAMEWELL FCI are for information only are not intended for installation purposes and are subject to change without notice No responsibility is assumed by Gamewell FCI for their use Clintonville Road Northford CT 06472 1610 USA Tel 203 484 7161 Fax 203 484 7118 by Honeywell International Inc All rights reserved Rev J page 1 of 2 Features 7100 series fire alarm control panel retains all the of a standard 7100 panel providing two signaling circuits supporting up to 394 addressable devices two appliance circuits an optional digital alarm transmitter etc See 9020 0044 for addition the network can be divided into regions Each can contain one or more 7100 panels Annunciation events within a particular region can be limited to just alphanumeric LCD displays of the 7100 systems that members of that region This is useful for multiple applications where each building would constitute own region Any INI 7100 module can be designated as global annunciator to annunciate events from all network Information Number Description Network Interface Unshielded Twisted pair Network Interface Fiber Optic Voltage Current Humidity Specifications Wire only VDC connection between P2 and 7100 BSM J2 amps All modes to 120 F 0 to 49 C max non condensing at F 32 C 1 2 W x 4 H x 3 4 D inches W x 10 H x 1.8 cm to 18 AWG twisted pair Up to 3,000 feet m between each node to 200 microns optimized for microns Up to 8 dB loss each node A M EW ELL FC I I 7100 PC B ER O PTIC C O N N EC TO R S O PTIO N A L S 232 1 3 3 4 J7 RX2 1 INI 7100 LED4 LED6 LED8 RC TX RX 2 DG N 2 3 4 5 6 7 LED3 LED5 LED7 DUP RX 1 RST O TE TH E B O A R D M O U N TS P SID E D O W N IN TH E C A B IN ET 1 must be installed Layout Ground Fault Supervision IN to enable supervision for ground faults the COM 1 wires connected to Terminals TB1 1 TB1 2 Jumper OUT for no ground fault super Note Remove for fiber optic connections Network ID switch binary Must be set to 1 through 64 Address 0 zero is not a address RS 232 port Connects to the 7100 Basic System connector J2 includes power connection Terminals 1 and 2 are Channel 1 COM1A 3 and 4 are Channel 2 COM2A Fiber optic transmitter for Channel 1 Fiber optic receiver for Channel 1 Fiber optic transmitter for Channel 2 Fiber optic receiver for Channel 2 Rev J page 2 of 2 Clintonville Road Northford CT 06472 1610 USA Tel 203 484 7161 Fax 203 484 7118