Gamewell-FCI MMI-10F Multi-Mod - 10 Input Module

Addressable Devices Series MMI 10F Ten Input Monitor Module Gamewell FCI Velociti Series multi mod ten input monitor module MMI 10F ten Style B Class B or five Style D Class A supervised initiating device IDCs that are suitable for a wide range of monitoring applications Velociti Series use a communication protocol that substantially increases the of communication between the sensors and certain Gamewell FCI analog fire alarm controls These devices operate in a grouped fashion If one of devices in the group has a status change the panel microprocessor stops the poll and concentrates on the single device The net effect is response speed up five times greater than earlier designs supervised circuit may be connected to any normally open contact device such manual stations tamper and supervisory switches waterflow switches heat 4 wire smoke sensors etc MMI 10F connects to the signaling line circuits SLC of the Gamewell FCI addressable series fire alarm control panels Each of the MMI 10F circuits its own address on the system SLC allowing each to be fully programmable its control by event sequence of operation address of the first circuit is set with a pair of rotary dials Each remaining circuit automatically assigned to its own subsequent address The MMI 10F module an address disable jumper matrix that allows a maximum of two unused to be turned off to free these addresses for other purposes An additional setting selects either Style B or Style D circuit configurations circuit has its own status LED that flashes to indicate proper polling and lights when the output has been activated Multi Mod units can be mounted in one MBB 2 cabinet Additional mounting include the MCH 6 chassis that can accommodate six Multi Mod modules MCH 6 chassis can be installed in a custom cabinet or it can be mounted in the cabinet that allows you to install up to six Multi Mod modules in one cabinet MMI 10F is ideal for applications where centralized location of circuits is required many as sixty initiating device circuits may be located in a cabinet that is only 12.6 x 24 W x 6.5 D in dimension saving valuable wall space in mechanical rooms and closets and reducing cost of installation Information Multi mod 10 input module Backbox 2 unit Backbox 6 unit requires MCH 6 6 Unit mounting chassis BENEFITS Each MMI 10F module ten Style B B or five Style D A individually device Ideal for applications Flexible jumper monitoring of open contact Removable wiring blocks allow of installation and feature one or two circuit to be Individual LED Terminal blocks can Ideal for retrofit 12 to 18 wire As many as sixty device in one 12 x 24 6.5 cabinet Two mounting cabinets for two MBB cabinet to six MBB cabinet MMO 6RS Bi color LEDs flash whenever the is addressed light steady red on Only the red LED operative in panels that not operate in mode Series MMI 10F Technical Specifications Velociti Series MMI 10F is designed to comply with following standards Standards UL 864 9th Edition 2572 for Mass Notification LISTINGS AND APPROVALS listings and approvals apply to the modules in this document In some cases certain or applications may not be listed by certain agencies or listing may be in process factory for latest listing status S1913 3023594 FDNY 219 02 E Vol VI 7300 1703 0124 9001 Certification a complete listing of all approvals and please visit E3 Series and are registered of Honeywell Inc is a registered trademark Underwriters Laboratories document is not intended be used for installation We try to keep our information up to and accurate We cannot all specific applications anticipate all requirements specifications are subject to without notice Voltage 15 32 VDC Current 3.5 mA Current 60 mA with all ten LEDs lit IDC IDC Wire Resistance 40 Ohms IDC Voltage 12 VDC IDC Current 1 mA Range 32 F to 120 F 0 to 49 C 10 to 85 non condensing 6.8 H x 5.8 W x 1.25 D 17.3 x 14.7 x 3.2 cm MBB 2 12.25 H x 9.25 W x 3.32 D 31.2 x 23.5 x 8.4 cm MBB 6 12.63 H x 24 W x 6.5 D 32.1 x 60.1 x 16.5 cm AND HUMIDITY RANGES system meets NFPA requirements for operation at 0 49 120 and at a relative humidity 93 2 noncondensing at 32 2 90 3 the useful life of the system s standby batteries the electronic components may be adversely affected extreme temperature ranges and humidity Therefore is recommended that this system and its peripherals be in an environment with a normal room of 15 27 80 more information more about Gamewell FCI Velociti Series MMI 10F and products available by visiting www Gamewell FCI com Gamewell FCI Clintonville Road CT 06472 1610 D 11 17 Honeywell International Inc