Gamewell-FCI RSSP Series Strobe Plates

Description RSSP Multi candela Strobe Appliances and Strobe offer a field selectable choice of four candela set including 15 30 75 or 110 CD versatile Strobe Appliances will satisfy virtually all for indoor wall mount applications models may be synchronized when used in conjunc with the SM SDM Sync modules or the FF8 power Synchronized strobes can eliminate possible re on the number of strobes in the field of view synchronized strobes offer an easy way to comply ADA requirements concerning photosensitive epilepsy Series RSSP Multi candela strobe plates are a cost way to retrofit required strobe appliances to bells chimes multitones or speakers and are easily to standard 4 backboxes or surface mounted the SBL2 R 71643 backbox candela wall mounted strobes are listed at 15 under UL 1971 and meet 75 candela intensity axis for ADA guidelines with low current draw Current for Multi Candela Models Average Current 24VDC 15CD 30CD 75CD 110CD 050A 081A 133A 161A RSSP PLATES Laboratories UL 1971 Approved to Part 15 California State Fire Marshal CSFM New City MEA European Community CE BFP Approved to meet or exceed NFPA ANSI Standards and Accessibility Guidelines Meets OSHA 29 Part Zero inrush Incorporates the RSS Non Sync Sync Strobe s Synchronization is achieved when used with the SM or DSM Sync Module or FF8 Power Supply All models meet ADA Guideline for minimum one flash per second from 20 31 VDC 24V models or 10.5 15.6 VDC 12V models Low current draw with temperature compensation to reduce power consumption and wiring costs Available in 15 15 75 30 75 and 110cd candela intensity wall mount Convenient Flush mounting to standard 4 square backbox or Surface Mount with SBL2 surface backbox Polarized 24 VDC models with wide listed voltage ranges using filtered DC or unfiltered VRMS input voltage Easy installation with In Out screw terminals using 12 to 18AWG wires Rev 1102 6 1 Specifications visual notification appliances shall be Series RSSP Multi Candela Strobe Appliances The Series RSSP Multi shall meet and be listed for UL Standard 1971 Emergency Devices for the Hearing Impaired for Indoor Fire Service The strobe shall be listed for indoor use and shall meet the requirements of FCC Part 15 Class B strobe appliances shall produce a flash rate of one 1 flash per second over the Regulated Input Voltage Range 16 to 33 VDC for 24 VDC models All inputs shall be compatible with standard reverse polarity supervision of circuit by a Fire Alarm Control Panel FACP When Strobe Plates are to be installed they shall be the Series RSSP Strobe Plate and shall have the same electronic circuitry as the Series RSSP Multi Candela All visual shall incorporate a Xenon flashtube enclosed in a rugged Lexan lens The Series RSSP Multi Candela shall be of low current design and shall have Zero Inrush The strobe intensity shall have a minimum of four 4 selectable strobe settings and shall be rated per UL 1971 for 15 30 75 or 110 candela wall mount The switch selecting the candela setting shall be located on the rear of the appliance in order to prevent tampering from persons The strobe shall be designed for 24 VDC two wire operation and when synchronization is shall be compatible with the SM DSM Sync Modules or FF8 Power Supply with built in Patented Sync The strobes shall not drift out of synchronization at any time during operation If the sync module or Power fails to operate i e contacts remain closed the strobe shall revert to a non synchronized flash rate The shall be designed for indoor surface or flush mounting Series RSSP Multi Candela Strobe Appliances shall incorporate a Patented Strobe Mounting Plate that shall allow to a single gang double gang 4 inch square An attaching cover plate shall be provided to give the an attractive appearance The Appliance shall not have any mounting holes or screw heads visible when the is completed Series RSSP Multi Candela Strobe Plate shall mount to either a standard 4 inch square backbox for flush mount or the SBL2 backbox for surface mounting notification appliances shall be backward compatible Information Number Series provide Synchronized Strobe with 71548 or 71549 Sync Modules or Gamewell FF8 NAC Power Candela Strobe Wall Mount 24VDC Red on a Plate RSSP 24MCW FR Candela Strobe Wall Mount 24VDC White on a Plate RSSP 24MCW FW Strobe 065 Amp Wall Mount 24VDC Red on a Plate RSSP 241575W FR Accessories for RSSP Series Surface Mount 4 Square x 1 1 2 D Red BB R Surface Mount 10 15 16 x 6 7 64 x 1 11 16 Red SBL2 R Surface Mount 4 Square x 2 3 16 D Red DBB R Surface Mount 5 Square x 1 9 16 D Red SHBB R Surface Mount 5 1 2 x 5 9 16 x 3 9 16 Red SBB R Plate 8 x 5 7 8 x 13 32 Red RP R and wiring information are provided for information only and are believed to be accurate Gamewell assumes no for their use Data and design are subject to change without notice Installation and wiring instructions shipped with the shall always be used for actual installation For more information contact Gamewell Gamewell Company Pleasant St MA 01721 in the USA 508 231 1400 888 347 3269 508 231 0900 2002 Rev 1102 6 2