Gamewell-FCI Wheelock MB Series, Motor Bells

Cooper Wheelock Series SERIES MOTOR BELL Cooper Wheelock Series MB bells provide a better engineered bell for fire and life safety alarm A number of improvements been built into the Wheelock MB bells including higher dBA current draw built in trimplate for mounting low frequency shells and low RFl noise motor for Series MB bells is a du high torque permanent magnet selected for its high performance long life DC motor bells are offered in and 10 gong sizes in both 12 and VDC models LSP MSP ISP HSPW LSPM plates are used for combina signaling using the MB Motor Bell visual strobe signals These 15 30 75 and 110 candela strobe are designed for Americans with Act ADA applications meeting or exceeding the latest of NFPA 72 the National Alarm Code ANSI 117.1 the National Standard for Acces and Usable Buildings and Facili and UL Standard 1971 Signal Devices for the Hearing Impaired new strobe products when specified and installed in ac with NFPA ANSI Standards provide the Equivalent Facilitation under ADA Accessibility ADAAG General Section by meeting or exceeding the illu which results from ADA intensity guidelines of 75 can at 50 feet This is an illumination 0.030 lumens per square foot foot MB LSPM UL listed for Fire Protective Service High sound output with low current draw Low frequency aluminum gongs pro better audibility through walls and other structures Both 6 and 10 gong sizes in 12 or 24 models Integral RFl suppression to minimize in noise on alarm circuits Mounting options for surface semi outdoor and concealed conduit in Built in trimplate makes semi flush simpler and less expensive Screw terminals permit fast in out field of 12 22 AWG wire Polarized for DC supervision of alarm Operate on filtered or unfiltered DC For combined audible bell and visual convenient retrofit plate as are available with 15 15 75 75 and 110 candela strobes refer to Sheet Series LS LSM MS Strobes for strobe specifica and technical information HSPW 6 HSPW 24 HFR 7 11 LSP 12 HFR 8 MSP 24 HFR HSPW 24 HFR LSPM 12 VFR Fire MSP 24 HFR LSP 12 HFR MSP 12 HFR ISO 9001 Company are provided for information only and are intended to be used for installation purposes and are to be accurate However no responsibility is by Gamewell FCI for their use subject to change without notice 2008 All Rights Reserved Rev B1 1of 2 Honeywell Company INFORMATION retrofit plates to be used with motor bells for combination signaling Wiring Mounting F G F F F F G F 2 to Spec Sheet for retrofit plate and information Built in trim plate eliminates need for SFP plate Typical dBA at 10 ft is measured in an anechoic All 12 VDC model bells are UL rated for 9.0 to VDC and all 24 VDC models for 18.0 to 31.0 Strobe Signals for 24 VDC operation are listed over a voltage range from 20 VDC to VDC Strobe Signals for 12 VDC operation UL listed over a voltage range of 10.5 VDC 15.6 VDC All DC models can be used with and unfiltered full wave rectified volt 1 Bell Models PRECEDING OR FACP NEXT OR 2 Strobe Models FACP FACP NEXT EOLR NEXT EOLR OPTIONS Mounting plates and backboxes ordered separately specify color SEMI FLUSH SURFACE CONCEALED CONDUIT OUTDOOR square FLUSH 4 square backbox 2 1 8 deep backbox SURFACE SBLI SBL 1 SBL for models with lens SURFACE SBL Clintonville Road Northford CT 06472 Tel 203 484 7161 Fax 203 484 7118 9020 0568 Rev B1 Page 2 of 2