Gamewell-FCI XP Mod MS-95 MS-95T Series Addressable Manual Pull Station

MS 95 MS95 T Manual Pull Station Complies with UL Standard 38 Meets ADA AG Controls and Operating Mechanisms requirements for a 5 lb pull force and with the 4 ft 1.2m mounting height Compatible with the following Gamewell FCI fire alarm control panels FACP 600 Series IdentiFlex 602 E3 Series ILI95 E3 Series S3 Series SLC95 PM Constructed of durable die cast metal Designed for use as a compact unit that blends with the Contains a recessed pull lever that prevents accidental a key reset option Used for surface or semi flush installations Shows a visible status LED Provides field programming Offers both wire and terminal block single action Available in the terminal block model MS 95T Gamewell FCI MS 95 MS 95T Addressable Manual Station is a non coded single action manual pull sta with a key lock reset feature Its rugged toggle switch offers exceptional resistance to accidental alarms by a sudden vibration or shock The MS 95 can be for surface and semi flush installations It is compati with the following Gamewell FCI addressable fire alarm panels FACPs 600 Series IdentiFlex 602 E3 Series ILI95 E3 Series S3 Series SLC95 PM MS 95 MS 95T are approved to UL Standard 38 for pull stations that comply with the architectural in all building interiors and is readily accessi in a fire emergency In addition the pull stations meet following American with Disabilities Act ADA AG and Operating Mechanisms Guidelines 4.1.3 5 lb 2 kg Mounting installation height of 4 ft 1.2m 42 106.48 cm maximum pull force to 48 121.92 cm max off the center activate the manual pull station press the lever inward Then pull the handle marked downward until the handle locks into place After handle is pulled this lever locks in the alarm position remains there until it is manually reset reset the alarm lever and release the front cover of the station insert and turn the key on the front of the pull This action unlocks the front cover and lowers the After the front cover is lowered the toggle switch is optional breakglass rod may be used with all pull sta The self clearing design prevents jamming of the and there is no danger to the operator from broken of glass Space is provided within the station for storage of an additional replacement glass rod MS 95 connects directly to the analog addressable cir via two wires The electronic circuitry has been to transmit data that can be interpreted as the three output operations normal standby operation alarm operation operation its standby mode of operation the pull station circuit the switch for alarm conditions A trouble condi occurs when the pull station is addressed by the con panel and either reports back a trouble response or not respond at all With the standard priority interrupt the MS 95 will report its condition instantly to the FACP Series is a registered trademark of Honeywell International Inc is a registered trademark of Underwriter Laboratories Inc GAMEWELL FCI are for information only are not intended for installation purposes and are subject to change without notice No responsibility is assumed by Gamewell FCI for their use Clintonville Road Northford CT 06472 1610 USA Tel 203 484 7161 Fax 203 484 7118 by Honeywell International Inc All rights reserved Rev D page 1 of 2 Information Number Description addressable manual pull station addressable manual pull station terminals action option reset option reset double action option rod backbox proof gasket for MS 95 station manual station backplate with 2.54 cm white stripe surface for key reset options program the MS 95 manual pull station to the address settings set the address DIP switch on the device circuit board All other programming is accom at the fire alarm control panel Specifications analog addressable manual pull station shall contain electronic interface circuitry required for individual identification alarm reporting and trouble supervi It shall communicate to the main control panel via the addressable circuit The single action station shall of a die cast aluminum housing fitted with a pull out which when operated locks in position after activat an alarm initiating contact Current Current Humidity to 120 0 to 49 non condensing VDC aluminum alarm red smooth gloss cast letters are high background for pull lever white glossed enamel A 0.8 mA A 1.5 mA MS 95 MS 95T MS 95 with key reset option Surface Backbox P N 28762 Surface Backbox P N 71961 H x 3.25 W x 1 1 8 D the backplate H x 8.25 W x 2.99 D cm H x 3.25 W x 1 1 8 D the backplate H x 8.25 W x 2.99 cm H x 3.25 W x 2.0 D from with Cat 60 Key H x 8.25 W x 5.08 D cm H x 3.25 W 2.375 D for 3 4 1.9 cm conduit 11.75 H x 8.25 W x 6.03 D cm H x 3.0 W x 3.25 D H x 7.6 W x 8.25 D cm Rev D page 2 of 2 Clintonville Road Northford CT 06472 1610 USA Tel 203 484 7161 Fax 203 484 7118