Honeywell HWF2-COM Series LTE IP Single or Dual Path Commercial Fire Communicators

Fire Alarm Communicators Series IP Single or Dual Path Commercial Fire Communicators HWF2 COM Series LTE IP fire communicators are single or dual path fire alarm communicators that offer contact ID reporting with any fire control panel FACP with a built in dialer include HWF2V COM Verizon LTE IP HWF2A COM AT T LTE IP models connect directly to the primary or secondary communication ports of a panel digital alarm communicator transmitter DACT selectable reporting paths include LTE cellular only IP only or IP primary with cellular backup All signals from the HWF2 COM Series are delivered to the network control center which routes highly encrypted cyber secure data packets via a customer provided Internet connection or LTE cellular to the appropriate central station The AlarmNet network control center is redundant and monitored 24 7 installation and programming through the AlarmNet 360 website using the hand held 7720P Programming tool or using the control programming mode for panels that support this option BENEFITS LTE and IP connection every day Three selectable paths LTE only IP only or Primary with LTE backup Requires no change to existing FACP Connects directly to primary and telephone of a DACT Plan choices range 5 minute 60 6 hour and 24 supervision Operates over the LTE HSPA 3G Works over any type of provided 10 100 based connection or WAN DSL or cable modem Built in stand alone QOS Quality of Service Data transmits over contact ID but is secured the industry encryption AES 256 bit Supports both dynamic or public and Static IP Reliable connection IP cellular connection every day Supply module board charging design battery Includes power and supervision Diagnostic LEDs signal and status Choice of LTE provider via conveys vital including strength path used when the message received 7720P Hand held for easy HWF2 COM LTE IP fire communicators operate over the most and common cellular networks including LTE 4G and3G station Primary Central Station ID two digits obtained from your Primary Subscriber ID four digits obtained from your monitoring Communication Module MAC ID and MAC CRC number located on outside of the box and inside of the module parameters are assigned by the monitoring station communications technology provides a highly reliable for the transmission of alarm signals The network extensive coverage in the United States and Canada The Network Control Center processes signals from powerful in multiple locations equipped with 24 7 infrastructure Redundant hardware servers hot back up databases and with battery back up at all locations to ensure continuity service Signals from AlarmNet are transmitted to central station using multiple communication paths consisting of the LTE radio network or toll free plain old telephone service Visit AlarmNet com to learn more Requirements UL COMPLIANCE meet UL864 NFPA ensure the following HWF2 COM Series must be installed in accordance with the Fire Protection Association NFPA standards 70 and 72 HWF2 COM Series must be mounted in the same room and within feet of the fire panel HWF2 COM Series and all equipment used for the IP connection router hub modem etc shall be listed and must be powered an unswitched branch circuit and be provided with standby power HWF2 COM Series must use the 7AH battery not included to 24 hour backup capability connect to any customer provided Ethernet 10 100 base connection LAN or WAN DSL or cable modem Selectable path feature allows the radios to be configured for a single dual path while providing appropriate supervision intervals based NFPA 72 requirements Selectable paths and supervision timing include Cell IP IP Cell Cell IP Path cellular Path IP Minutes Minutes Path IP cellular Hours Path cellular Minutes Path IP cellular Minutes IP Cell Path IP cellular Hours an event occurs the FACP goes off hook to dial the central The HWF2 COM Series dialer capture module detects the off condition and provides the fire panel with a dial tone When the panel detects the dial tone it begins dialing the central station the dialing is completed the dialer capture module returns a to the fire panel The fire panel then sends the contact ID to the dialer capture module which in turn sends a signal after report is successfully received from the fire panel The dialer nodule sends the contact ID reports to the HWF2 COM communications module When all the reports are sent the fire goes on hook The HWF2 COM Series communications then transmits the messages to the central station either over LTE network or the Internet dependent on configuration Communicator Panel Capability HWF2 COM Series is compatible with fire alarm control panels use the Contact ID communications form as described in the SIA standard to Program HWF2 COM communicator series can be pre programmed using 7720P programmer to enter all central station information This is to the HWF2 COM communicator panel memory When the is installed at the site and connected to the Internet it registers with the AlarmNet Receiver most installations the only required parameters are Primary City ID two digits obtained from your monitoring station 2 of 3 DH 62011 A 05 09 2019 by Honeywell Inc All rights Unauthorized use of document is strictly document is not intended be used for installation We try to keep our information up to and accurate We cannot all specific applications anticipate all requirements specifications are subject to without notice of origin US AND EXTERNAL HARDWARE 3dBA gain external remote antenna SNA to N Adapter Works with HWF2 COM and IPGSM 4G 50 ft antenna cable low loss The CELL ANT3DB and the WA7626 CA are both for installing an external antenna along with the 50 ft antenna cable ACCESSORIES HWF2V COM HWF2A COM and IPGSM 4G hand programmer Plug in transformer box for HWF2V COM and IPGSM 4G communicators Battery 12 Volts 7AH sealed LISTINGS AND APPROVALS listings and approvals below apply to the HWV2V panel In some cases certain modules may not be by certain approval agencies or listing may be in Consult factory for latest listings Listed S789 7300 1545 0199 pending COA 6219 pending Series Technical Specifications 120VAC 60Hz 0.5A 18VDC 50VA 12 V 7.0 AH lead acid battery not supplied charging current 1 Amp maximum discharge current Standby 230mA Active SPECIFICATIONS 14.875 H x 12.75 W x 3.0 D H x 32.4cm W x 7.6cm D Red DIMENSIONS 5.3 lbs 6.94kg 15.625 H x 13.79 W x 9.25 D H x 34.9cm W x 23.9cm D AND HUMIDITY RANGES system meets NFPA requirements for operation at 0 and at a relative humidity 93 2 RH at 32 2 3 However useful life of the system standby batteries and the components may be adversely affected by temperature ranges and humidity Therefore it is that this system and its peripherals be in an environment with a normal room of 15 27 LINE INFORMATION LTE Digital Cellular Fire Alarm and Internet Panel Models HWF2V COM Verizon LTE IP HWF2A COM AT T LTE IP models include cabinet with key and lock