Hochiki 1-5028 FNV-ATM Install Rev E (08 07)

FNV ATM Transponder Module FNV ATM provides a method of interfacing audio either into the Hochiki system or from the evac system into an external paging system has several methods of accomplishing this and is field selectable for its It is capable of being activated by either contact closure or signal by use of a VOX Voice Activation Circuit Its input may be Line 1 Vrms into 600 Ohms 25 Vrms or 70 Vrms input and output signals are isolated so systems will not experience loop problems FNV ATM mounts into standard 3 snaptrack The board also mounting holes at the corners for stand off mounts where required 1 Board 1 Push To Talk 2 V 24V DC 0.10A 3 ALARM 4 AUX SIG 5 AUX PTT 6 Signal 7 Aux Audio PreAmp 1 2 Audio input Bal Line 1V 600 Ohm 25 70 1 2 N O Dry Contact 3 4 Bal Line output Q R 5 M B C D Y PTT Function Audio Path Gain Audio Input Dry Contact Audio Input 24 VDC 0.015A Standby 0.035A Active 3 x 3 holes 0.160 dia 0.25 centered corners 1 5028 Rev E 1 of 4 Village Drive Suite 100 Park CA 90621 2268 Technical Support Audio into the Evax System dry relay contact provides activation 2 Settings R C 5 1V 25V 70V Y V FNV 25 wiring connections wire clamp screw 14 18 AWG wire clamp screw 12 18 AWG wire entry terminal 18 26 AWG gauge determined by circuit load Q R 5 M B C D Y 600 Ohm 70V selected at J4 supplied dry relay contact activate aux audio 3 Audio input w VOX Audio signal input provides activation FNV 25 Settings P C 1 1V 25V 70V X V wiring connections wire clamp screw 14 18 AWG wire clamp screw 12 18 AWG wire entry terminal 18 26 AWG gauge determined by circuit load Q R 5 M B C D 600 Ohm 70V selected at J4 Y X jumper selects VOX activation Signal alone enables input 1 5028 Rev E 2 of 4 Village Drive Suite 100 Park CA 90621 2268 Technical Support System driving Audio System Evax system generates activation wiring connections wire clamp screw 14 18 AWG wire clamp screw 12 18 AWG wire entry terminal 18 26 AWG gauge determined by circuit load Settings B M 1V X 4 Q R 5 M B C D Y ohm out dry contact provided needed to activate input external unit relay is FNV ATM to be mounted within Hochiki System cabinet System driving Audio System VOX circuit provides activation on presence of audio signal 5 wiring connections wire clamp screw 14 18 AWG wire clamp screw 12 18 AWG wire entry terminal 18 26 AWG gauge determined by circuit load VDC Settings P C 5 1V X V Q R 5 M B C D Y or 70V is at J4 ohm out dry contact available needed to activate input external unit to be mounted within external system cabinet 6 Audio input w VOX Audio signal input provides activation Wiring when used in addition to other Audio Sources wiring connections wire clamp screw 14 18 AWG wire clamp screw 12 18 AWG wire entry terminal 18 26 AWG gauge determined by circuit load Settings P C 1 1V 25V 70V X V EVX 25 Q R 5 M B C D Y 70V selected at J4 600 Ohm FNV 25 X jumper selects VOX activation Signal alone enables input NOTE Additional ATM and FNV RM Remote Microphones 1 5028 Rev E 3 of 4 Village Drive Suite 100 Park CA 90621 2268 Technical Support FNV Audio into FNV MP 7 600 ohm balanced line 25VRMS or 70 VRMS input Neg Red required if external source is other than ohm 1VRMS balanced Red Neg Input Dry activation Figure 3 for jumper settings wiring connections wire clamp screw 14 18 AWG wire clamp screw 12 18 AWG wire entry terminal 18 26 AWG gauge determined by circuit load 1 5028 Rev E 4 of 4 Village Drive Suite 100 Park CA 90621 2268 Technical Support