Hochiki FNV Components

Break Out Card System Control Module Interface Communications Controller Amplifier switching relay Amplifier switching relay Class two FNV 25E 50E 100E amplifier modules in remote distribution One required when adding back up amplification to a Dual channel Uses an addition slot on a FNV MBR digitally stored Message Control Has two RS232 com ports required for each Distributed Amp when automatic switching amplification is needed a single Channel system the back up amplifier can be located in any panel On a Dual Channel system an additional FNV AMI card FNV E Amplifier assembly is required the represents the largest amplifier in the system 25 50 100 required for each Distributed Amp plus the amplifier when switching redundant amplification is needed Class wiring a single Channel system the amplifier can be located in any panel On a Dual Channel system an additional FNV AMI card FNV E Amplifier assembly is required the represents the largest amplifier in the system 25 50 100 to provide terminal connections from 10 Pin ribbon cable for wiring 2 required when Dual Channel Back Up Amplification is required DCC is located in the Master Panel and each Distributed Panel the DCC the connection point for the NETCOMM communications The Data loop be wired style 6 or 7 Style 7 preferred must have return data loop Card typically preprogrammed from the factory termination for Fiber Optic communications between the Master and the Distributed Panels Panel Fiber Optic card 1 per system required when Style 7 Fiber communications is used The FNV FO7 card converts the secondary 7 data loop to a data signal that can be sent on the Fiber Optic loop 4 supervised Class Fire Phone circuits in distributed panel 4 16 circuits When more then one is used in a FNV DP panel a FNV card is required for each terminal card that must be used with the 2nd 3rd 4th FNV FPI in a DP panel break out card that must be used with the 2ND 3RD 4TH FNV FPI in a DP panel This card aligns all 4 Fire Phone circuits vertically station reverse polarity relay for NYC applications conventional control input interface trigger Required when any triggers other the FNV Intelligent Interface Provides 16 inputs control for up to 7 additional FNV XI input cards 128 inputs System for up to 16 FNV II cards 2048 inputs TTL or dry contract input accepts a reverse polarity NAC circuit trigger interface when a Master Panel is needed to communicate with Master Panels running their own systems Phone Output Adapter Phone Output Adapter Network Bridge Optic Style 7 card Optic Tranceiver Phone Interface Interface Card Phone Relay Hochiki FNV High Rise Voice Evacuation System Components DIAG PGM SCAN Rev 1.0 3 2 1 Village Drive Suite 100 Park CA 90621 2268 Technical Support sign RS232 Lamp Card Board Relays Board Remote Fire Phone card Printer Interface Microphone Control Fire phone Assembly Panel interfaced board for RS232 data into FNV using a Fire Panel printer port also has a parallel port for connection a Fire Panel printer Interfaces FNV ASC Isolator card Isolates the ground from the RS232 from The Fire Alarm Panel LED only card for annunciation at Master Panel 4 Class speaker Loop outputs A maximum 2 FNV MBK cards provide 8 B or 4 Class A circuits per Distributed panel One additional for 8 Class or 4 Class Distributed Panel Circuits the 4 card slots can be extended to MAX 7 for FNV FPI and 2 FNV MBK speaker cards Loop Zone splitter function Panel s Fire Phone Card connects to the DCC to Fire Fighter Phone communication Panel s replacement Fire Phone Handset Plate Interface PC board Microphone System Control and status display Panel mounted flashing FIRE sign Utilizes a row of the Master Panel control output interface Provides 16 outputs control for up to 7 additional FNV XO output cards outputs System capacity for up to 16 FNV OI cards outputs TTL output 24VDC at 1.5 Amps and battery charging for use with Master Panel switches and LED s for manual control at Master up to 8 Switch LED Cards 128 Switches 16 FNV SSC cards can be used for a System of 2048 Switches Field Additions or only 16 additional inputs per card Used with FNV II recommend a separate mounting cabinet 8 outputs per card Used with FNV OI card a separate mounting cabinet 4 Class B speaker circuits into 8 Class B circuits requires a separate mounting cabinet Audio Matching Circuit Telephone Module balance Line telephone or paging module Used connect to an existing telephone or paging system into FNV Voice System 600 ohm 25 70 VRMS input Class A Zone Adapter Card 4 Class B speaker circuits into 4 Class A circuits requires a separate mounting cabinet Output Interface Panel Power Supply Input Interface Adapter Card Interface Card LED Card Scan Card LED 2 2.1 2 3 LED 1 2 3 4 5 6 7 8 9 10 11 J2 J3 P R STATUS LED 2 PWR LED 2 I E 1 2 3 4 5 6 7 8 9 10 11 2 3 4 2 3 4 2 3 4 2 3 4 list on this sheet is intended for purpose please contact Hochiki America Technical for UL listing information CONTROL