Honeywell 5000 Thermostat User Manual

Non Programmable Series installation the wallplate from the thermostat follow directions below for mounting Remove battery holder Pull here to remove wallplate from new Pull wires through wire hole Position wallplate on wall level and mark positions with pencil Drill holes at marked positions as shown then tap in supplied wall anchors Place wallplate over anchors insert and mounting screws 3 16 for 7 32 for hole options wires in this area factory jumper for two batteries for primary backup power C for primary AC power if batteries are installed terminal designations areas below apply only to TH5320U TH5220D or as otherwise noted Terminals power from cooling power from heating relay stage 1 Heat relay stage 2 contactor stage 1 contactor stage 2 relay common For 2 transformer use common wire from transformer Pump Terminals power from cooling power from heating Changeover valve contactor contactor stage 2 only relay Auxiliary Emergency heat relay output when set to Em Heat common Rc Rc conventional systems areas below apply only to TH5320U TH5220D or as otherwise noted 1 joined by jumper common 3 relay 1 joined by jumper contactor common 3 relay relay joined by jumper 20 valve terminal 1 20 valve terminal common 3 20 valve terminal System transformer 20 5 open zone valve 5 System transformers specifications 18 to 22 gauge thermostat wire cable is not required Power supply Provide disconnect means cooling transformer 1 2 heating transformer 1 2 contactor common 3 4 relay relay joined by jumper 1 open zone valve common 3 R overload protection as required Remove jumper for 2 transformer systems Optional 24VAC common connection Common connection must come from cool transformer Installer Setup set system type to Only 1 joined by jumper common 3 relay relay System Fan System 1 joined by jumper contactor common 3 relay System transformer 6 Heat relay stage 2 System transformers 6 Heat relay stage 2 1 joined by jumper contactor stage 1 common 3 relay stage 1 relay contactor stage 2 cooling transformer 1 2 heating transformer 1 2 contactor stage 1 common 3 4 relay stage 1 relay contactor stage 2 Installer Setup set system type to Conventional Installer Setup set changeover valve to or B Installer Setup set system type to Heat Pump Installer Setup set system type to Heat Pump In Installer Setup set system type to Heat Pump L terminal sends a continuous output when is set to Em Heat Connect Honeywell zoning panels to switch the to Emergency Heat heat pump systems areas below apply only to TH5320U TH5220D or as otherwise noted relay contactor stage 2 output when set to Em Heat 11 1 joined by jumper contactor stage 1 common 3 Heat Pump only 9 Changeover valve 7 Heat Pump only 10 Changeover valve 7 Auxiliary Emergency heat relay contactor stage 2 output when set to Em Heat 11 1 joined by jumper contactor stage 1 common 3 relay relay 1 joined by jumper contactor common 3 1 joined by jumper contactor common 3 Heat Pump Changeover valve 7 Heat Pump TH5220D only 8 Changeover valve 7 Auxiliary Emergency heat relay Heat Pump only 8 Changeover valve 7 Auxiliary Emergency heat relay 1 joined by jumper contactor common 3 relay relay output when set to Em Heat 11 mounting Push excess wire back into the opening Plug wall opening with non insulation Align the 4 tabs on the wallplate corresponding slots on the of the thermostat Push gently until the thermostat in place output when set to Em Heat 11 Notes on page 3 setup the procedure below to configure thermostat to match the installed system and customize operation as desired To begin press and hold the s FAN buttons until the display Press s or t to change settings Press NEXT to advance to next Press DONE to exit and save function areas below apply only to TH5320U TH5220D or as otherwise noted options factory default in bold 1 System type heat 1 cool conventional heat 1 cool heat pump no aux heat Heat only 2 wire systems 3 wire zone valves Series 20 normally open zone valves heat 1 cool heat pump with aux heat heat 2 cool conventional heat 1 cool conventional heat 2 cool conventional heat 2 cool heat pump no aux heat TH5320U only Heat only with fan Cool only 3 heat 2 cool heat pump with aux heat TH5320U only Changeover valve O B terminal energized in cooling Changeover valve O B terminal energized in heating Gas or oil furnace equipment controls fan in heating furnace thermostat controls fan in heating gas or oil furnaces of less than 90 efficiency steam or gravity systems hot water systems furnaces of over 90 efficiency electric furnaces gas or oil furnaces of less than 90 efficiency steam or gravity systems hot water systems furnaces of over 90 efficiency electric furnaces gas or oil furnaces of less than 90 efficiency steam or gravity systems hot water systems furnaces of over 90 efficiency electric furnaces 2 Changeover valve terminal 3 Fan control 5 Stage 1 heat cycle cycles hour 6 Stage 2 heat cycle heat rate CPH 7 Auxiliary heat rate CPH Only TH5320U 3H 2C Heat cycle rate options 2 4 6 7 8 10 11 or 12 CPH function areas below apply only to TH5320U TH5220D or as otherwise noted options factory default in bold 9 Stage 1 compressor Recommended for most compressors rate CPH cycle rate options 1 2 4 5 or 6 CPH 10 Stage 2 compressor Recommended for most compressors rate CPH cycle rate options 1 2 4 5 or 6 CPH 12 Manual Auto 14 Temperature 15 Compressor Manual changeover Heat Cool Off c