Honeywell 6160RF Installation And Setup Manual

Downloaded from www Manualslib com manuals search engine K0903V1 2 06 Rev B ADEMCO 6160RFKeypad TransceiverInstallation and Setup Guide GENERAL INFORMATION The ADEMCO 6160RF keypad transceiver is a combination unit that combines the functions of the following devices 6160 Alphanumeric Addressable Keypad 5881H RF Receiver 5800TM Transmitter Module The 6160RF Keypad Transceiver may be used on any control panel that supports 5800 Series wireless devices e g VISTA 10P VISTA 15P VISTA 20P FEATURES Supports wireless key transmitters e g 5804 and bi directional transmitters e g 5804BD 5828 5828V Supports wireless keys with high security encryption capability e g 5804E Provides a nominal range of 200 feet for RF transmitters some transmitters have a shorter range Supports RF jam detection when the receiver is enabled Capable of sending status signals Armed Ready etc to bi directional units such as 5804BD 5804BDV and 5828 5828V UUUULLLL The following 5800 series transmitters are not intended for use in UL installations 5802 5804 5804BD 5804BDV 5804E 5814 5816TEMP 5819 5819BRS 5819WHS 5828 5828V and 5850 INSTALLING THE 6160RF Locate the 6160RF in an area and at a height where it is convenient for user operation The 6160RF must be at least 10 ft from the control panel to ensure proper operation of the RF receiver Mounting and Wiring The 6160RF has terminal blocks for connection to power and data wires Removing the keypad case back provides access to the terminal blocks The 6160RF can be surface mounted directly to walls or to a single or double gang electrical box Follow these steps to mount and wire the keypad 1 Push the two case release snaps at the bottom of the keypad with the blade of a medium screwdriver this will push in the release snap then pull that side of the case back away Insert the screwdriver in the side of the keypad between the front and back case and gently twist to release the side locking tab Repeat for the other side Refer to Figure 1 for location of the case back release snaps and locking tabs ARMEDREADYMOUNTINGRELEASESNAPSNOTE TO REMOVE REAR COVERPUSH IN THE TWO MOUNTINGSNAPS LOCATED ALONG THE BOTTOM OF THE KEYPADAND LIFT COVER UP 6160RF 003 V1LOCKINGTAB Figure 1 Removing the Case Back 2 Pass the wiring from the control panel through the opening in the case back see the control panel instructions for proper run lengths a If surface wiring is being used wiring may be routed through the top or the bottom left side breakout in the case back The breakouts must be punched out using a screwdriver before mounting the case back b If desired wires may be strain relieved to the wire tie point on the inside of the case back with a tie wrap not supplied 3 Mount the case back to a wall or to an electrical box using the 25mm long self tapping screws supplied mollies for drywall are not supplied 4 Connect the power and data wires from the control panel to the terminals on the 6160RF as indicated in Figure 2 and Table 1 G6160RF 002 V1Y WIRING TERMINALS TO CONTROL PANEL Figure 2 6160RF Wiring Details firealarmresources com from www Manualslib com manuals search engine 2 Table 1 Wiring Table Keypad Control Panel Wire Color G cid 1 Data Out Data In Green Aux Pwr GND Black Aux Pwr Red cid 2 Y Data In Data Out Yellow 5 Reattach the keypad to the mounted case back Attach the top of the keypad first and then press the bottom section down until it snaps into place securely 6 Peel off protective film on the LED panel and install the keypad labels as required APPLICATION GUIDELINES FOR THE 6160RF Use the following guidelines when planning an installation If And Then This is the only transceiver on the system You want to use both the receiver and transmitter function on a single partition system Set the keypad to a device address assigned to the desired partition Enable the receiver Program a system House ID in the control panel this will enable the transmitter function Set the wireless devices that will communicate with this 6160RF to the same system House ID You want to use only the transmitter function on a second partition Set the keypad to a device address assigned to the desired partition Disable the receiver Program a DIFFERENT House ID in the 6160RF than is programmed in the control panel Set the wireless devices that will communicate with this 6160RF to the same House ID as the 6160RF There is another receiver or transceiver on the system You want to use only the transmitter function on a single partition system Set the keypad to a device address assigned to the Partition 1 Disable the receiver Program a House ID in the 6160RF that matches the system House ID programmed in the control panel Set the wireless devices that will communicate with this 6160RF to the same House ID Notes On VISTA 40 panels and above wireless keypads e g 5804BD can only be used on a single partition This partition is programmed in field 1 48 and must match the partition assigned to the 6160RF Wireless keys can be used on more than one partition using a House ID programmed in the 6160RF and the devices In this case the wireless keys must be assigned to the same partition as the 6160RF On VISTA 20P panels the 6160RF will use the House ID programmed in the panel for the partition to which it is assigned Wireless keypads can only be used on Partition 1 PROGRAMMING THE 6160RF Refer to the following procedure to program the 6160RF STEP DESCRIPTION DISPLAY CHOICES 1 Enter the program mode by pressing the 1 and 3 keys simultaneously for a few seconds within 60 seconds after applying power 2 Keypad Address Enter the two digit keypad address Press the key to continue Notes 1 Refer to the control panel installation instructions for the acceptable keypad addresses 2 On the VISTA 40 and above the 6160RF partition assignment must match the RF keypad partition assignment programmed in field 1 48 CON ADDRESS CON ADDRESS CON ADDRESS CON ADDRESS XX XX XX XX 00 31 3 Receiver Enable Enter 1 to enable or 0 to disable Receiver Enable the receiver if RF transmitters or wireless keypads are programmed into the control and no other receivers are enabled Press the key to continue RECEIVERRECEIVERRECEIVERRECEIVER ON 0ON 0ON 0ON 0 OFF OFF OFF OFF 1 ON 0 OFF firealarmresources com from www Manualslib com manuals search engine 3 STEP DESCRIPTION DISPLAY CHOICES 4 Receiver Address If receiver is enabled enter the two digit receiver address 01 30 Note Refer to the control panel installation instructions for the acceptable receiver addresses Press the key to continue REC ADDRESSREC ADDRESSREC ADDRESSREC ADDRESS XXXXXXXX 00 30 5 House ID This prompt will only appear if the receiver is disabled If the receiver is enabled the 6160RF will use the House ID programmed in the panel Refer to Application Guidelines section when selecting a House ID To program a House ID Enter 01 31 To disable the transmitter Enter 00 Note Each device that will receive status from the 6160RF must be set to the same House ID as the 6160RF refer to Application Guidelines section Press the key to continue HOUSE ID HOUSE ID HOUSE ID HOUSE ID XX XX XX XX 00 31 6 Enable High Security Mode Enter 1 to select High Security Mode Note If the High Security mode is enabled the 6160RF will only recognize encrypted devices If this mode is disabled the 6160RF will process commands both encrypted and non encrypted devices Press the key to continue HIGH SECURITYHIGH SECURITYHIGH SECURITYHIGH SECURITY OFF 1OFF 1OFF 1OFF 1 ONONONON 1 Enable 0 Disable 7 Disable High Security Devices Press the key to skip this prompt and exit Program Mode Notes 1 The key must be pressed several times in order to save the programmed data 2 If you need to disable encrypted devices refer to the Disabling High Security Devices section DISABLE HS DEV DISABLE HS DEV DISABLE HS DEV DISABLE HS DEV NO 1NO 1NO 1NO 1 YESYESYESYES 1 YES 0 NO When operating the system in High Security mode 5804BD wireless keys will still function If you want the system to recognize only encrypted wireless devices program only encrypted devices in the system ACTIVATING HIGH SECURITY DEVICES This following procedure should be followed if using High Security encrypted devices STEP DESCRIPTION 1 Follow the normal procedure for programming the device into the control panel refer to the Installation Instructions for the device that you are programming Exit out of Programming Mode 2 Put the control panel in Go No Go Test mode See the Installation Guide for the panel being installed 3 Follow the instructions supplied with each wireless device to enroll the device in High security mode After each device is enrolled the 6160RF will momentarily display DEVICE along with the device number and its serial number Note The 6160RF will support a maximum of 8 devices If you attempt to enroll additional devices the keypad will display NUMBER DEVICES DISABLING HIGH SECURITY DEVICES This mode gives you the ability to disa