honeywell 8000 thermostat user manual

Table 1 Installer Setup 1 Installer Setup functions Options factory functions Options factory sysTem TesT Installer Test is part of the Installer Setup Menu the Installer System Test by entering the Installer and pressing t repeatedly until appears lamp change Intel RecoveryTM periods in bold calendar days periods Wake Return Sleep periods Wake Sleep compressor time options 0 temperature stop temperature stop format fan heat fan cool Lockout Max heat temperature is 90 32 options 40 89 to 32 Min cool temperature is 50 10 options 51 99 to 37 time time runs for 90 seconds call for heat ends runs for 90 seconds call for cooling ends locked locked temperature temperature offset in bold temperature recommended if inside tempera is consistently over if inside tempera is consistently under temperature recommended if inside tempera is consistently over if inside tempera is consistently under offset options 3 2 1 2 3 1.5 to reset installer options program schedule to default TesTs the system heating cooling fan and emergency heat tests vary by thermostat and system type 2 Installer System Test Type Status Number Description Test 1 System and on stage on on on stage heat heat on stage heat heat on Heat and fan on heat on 4 Test the DONE button to exit the Installer System Test arrow to change test and system status as NUMBER STATUS 2 3 System System DONE to exit DAMAGE HAZARD protection is bypassed during testing To equipment damage avoid cycling the compres quickly seTuP SYSTEM 8000 seTuP and TesT POckeT GuIde HOLD and hold these two blank buttons until the changes 1 Installer Setup 1 Installer Setup 1 Installer Setup functions Options factory functions Options factory functions Options factory type stage heat rate arrows to change settings as required DONE to exit and save settings seTuP funcTIOns option and default settings vary by thermostat 1 Installer Setup functions Options factory first two second two Month format in bold 2000 2099 2100 2178 2006 Other options 0 99 Other options 1 12 Other options 1 31 programming control valve terminal heat fossil kit stage cycle stage cycle in bold heat 1 cool Conv heat 1 cool heat no Aux heat only 2 wire only with fan water Series 20 only heat 1 cool heat with Aux heat heat 2 cool multistage heat 1 cool multistage heat 2 cool multistage heat 2 cool heat pump Aux heat heat 2 cool heat with Aux heat heat equipment heating fan furnace thermo controls heating fan valve in cooling valve in heating backup heat fuel backup heat fossil fuel kit backup heat controls heat outdoor required options 1 options 1 stage cycle rate stage heat rate heat rate Manual auto in bold or oil furnaces of than 90 or gravity water systems or fur of 90 efficiency furnaces options 1 or oil furnaces of than 90 efficiency or gravity water systems or fur of 90 efficiency furnaces options 1 auxiliary heat electric furnaces or gravity water systems or fur of 90 efficiency or oil furnaces of than 90 efficiency options 1 auxiliary heat electric furnaces or gravity water systems or fur of 90 efficiency or oil furnaces of than 90 efficiency options 1 on keypress backlight re 24VAC connection changeover changeover in bold tempera 3 apart 1.5 options 2 9 2 to daylight time through to daylight time 2007 and savings time is off remote sensor sensor display sensor for con select heat pumps sensor options 15 20 30 35 40 9.5 7 options 40 45 55 60 4.5 to runs to help run time 1 month run time 3 months run time 6 months run time 9 months run time 1 year run time 3 years calendar days calendar days calendar days changeover savings sensor pump com lockout pump auxil lockout filter reminder pad reminder in U S A on recycled containing at least 10 paper fibers and Control Solutions International Inc Douglas Drive North Valley MN 55422 Limited Honeywell Limit Dynamic Drive Ontario M1V 4Z9 U S Registered Trademark 2006 Honeywell International Inc Patent No 6595430 D509151 other Pending All Rights Reserved M S Rev 09 06