Home » Invensys MSC-UC-PMF Pneu Manifold Assem
File preview
Click the button below to download immediately for free
Show text preview
ENVIRONMENTAL 16 Unit Controller Filter) assembly distributes MSC-UC-PMF Manifold air to the MSC-UC-PO MicroSmart Unit Controller Output card which can be used with the DCM-UC, or the MSC-UlOOO. The MSC-UC- also provides an intermediate connection the lines. An air filter is provided for removing dirt, and other debris that may accumulate the air line are the MicroSmart Unit with these Filter) and Pneumatic Manifold Assembly package of hardware the single or its installation enclosure which will also house the MicroSmart Unit installation process for the MSC- beginning visually inspect the unit for any obvious defects to make sure all parts are included. any flaws are contact your local Robertshaw office or One Nl OO-690061 One N406-253 Guide. bag that includes the terminal strip (1) . . . . . . . . -01 -pressure gauge (1) main air manifold 26 l/8 elbow (1) OO-2530 3/8 elbow (1) OO-2356 (6 OO-250015 . union (1) KEP nuts (11) (1) pneumatic The MSC-UC-PMF MSC-UC-PO connection an on the unit controller. The MSC-UC-PMF no electrical power. a pneumatic device and in single (ENC-001) or dual (ENC-002) with the associated unit controller. Complete and installation are provided on following page. to install the Pneumatic refer to the illustrations on the following pages follow these Assembly. items from the hardware package. the tubing terminal strip over the two screws the gauge tee over the two screws at the of the bracket with the open end of the tee the interior of the enclosure and the tubing pointing toward the top of the enclosure. assembly mounts on the enclosure the top of the backplate place with two nuts. . 1). y Figures 2 and 3.) Tighten with . nuts. manifold has nine terminals. These sealed and the installer must drill out those a particular application. Use a l/l 6 bit. over terminals assembly on a flat surface available). Drill carefully so that only the flashing through. thin. Before drilling, place in a vise if one drilling, remove any plastic particles the manifold. Eight of the terminals may be for output tubing and one may be used for the air gauge. Fit the black elbow tightening with the barbed end pointing direction as the manifold the open end of the manifold. the Slip the main air manifold with elbow over the studs and secure with nuts. The manifold should face the rear of the enclosure. Connect brass elbow to main air gauge. Use pipe to seal.
ENVIRONMENTAL 16 Unit Controller Filter) assembly distributes MSC-UC-PMF Manifold air to the MSC-UC-PO MicroSmart Unit Controller Output card which can be used with the DCM-UC, or the MSC-UlOOO. The MSC-UC- also provides an intermediate connection the lines. An air filter is provided for removing dirt, and other debris that may accumulate the air line are the MicroSmart Unit with these Filter) and Pneumatic Manifold Assembly package of hardware the single or its installation enclosure which will also house the MicroSmart Unit installation process for the MSC- beginning visually inspect the unit for any obvious defects to make sure all parts are included. any flaws are contact your local Robertshaw office or One Nl OO-690061 One N406-253 Guide. bag that includes the terminal strip (1) . . . . . . . . -01 -pressure gauge (1) main air manifold 26 l/8 elbow (1) OO-2530 3/8 elbow (1) OO-2356 (6 OO-250015 . union (1) KEP nuts (11) (1) pneumatic The MSC-UC-PMF MSC-UC-PO connection an on the unit controller. The MSC-UC-PMF no electrical power. a pneumatic device and in single (ENC-001) or dual (ENC-002) with the associated unit controller. Complete and installation are provided on following page. to install the Pneumatic refer to the illustrations on the following pages follow these Assembly. items from the hardware package. the tubing terminal strip over the two screws the gauge tee over the two screws at the of the bracket with the open end of the tee the interior of the enclosure and the tubing pointing toward the top of the enclosure. assembly mounts on the enclosure the top of the backplate place with two nuts. . 1). y Figures 2 and 3.) Tighten with . nuts. manifold has nine terminals. These sealed and the installer must drill out those a particular application. Use a l/l 6 bit. over terminals assembly on a flat surface available). Drill carefully so that only the flashing through. thin. Before drilling, place in a vise if one drilling, remove any plastic particles the manifold. Eight of the terminals may be for output tubing and one may be used for the air gauge. Fit the black elbow tightening with the barbed end pointing direction as the manifold the open end of the manifold. the Slip the main air manifold with elbow over the studs and secure with nuts. The manifold should face the rear of the enclosure. Connect brass elbow to main air gauge. Use pipe to seal.