Invensys DCM-1000 Distributed Control Module

DCM 1000 Control Module in U S A 1 GUIDELINES INCLUDED THIS PACKAGE REQUIREMENTS Switch and EMI Grounding WIRING 350A to DCM 1000 Controller Trunk Wiring OUTPUT JUMPERS AND INDICATORS SUPPORT Start Up Repair Distributed Control Module DCM 1000 to any MicroSmart controller in the DMS family and acts as a area controller a DMS 350A Two controller trunks are for interfacing of up to 62 controllers The has an integral rechargeable battery which backup operation of its clock as well as retention for time of day schedules table point records and point configuration DCM trunk to the DMS 350A is a 2 wire One 6 position connector is provided on controller for termination of redundant trunks One connector provides failsafe input output between the DCM 1000 and controllers is via a two wire 51.2k baud trunk NUMBER DCM 1000 DCM 1000 I LISTINGS UL 916 Energy Management Complies with FCC Class CAPACITY 250 I O and software points of 64 S S points plus MicroSmart points PROGRAMMING 400 lines of code available 100 UDPs max TO DCM 1000 COMMUNICATIONS 2 wire RS 485 redundant trunks Rate 51.2 Kbps standard Length 4,000 feet maximum TO CONTROLLER Two 2 wire RS 485 redundant trunks of 62 controllers Rate 51.2 Kbps standard Length 4,000 feet maximum Master Processor and Unit Watch Dog Timers Fail Safe Input and Trunk A Communication Status LEDs BACKUP 72 hour rechargeable battery 32 S S schedules 6 events day CYCLING 4 Interval off time pairs per load RAM and Clock days 3 holidays begin times COMPENSATION On duty and night setback Guidelines TIME OPTIMIZATION Applicable to each start point autotuning of start time parameters AIR OPTIMIZATION For up to 4 air units SOFTWARE POINTS Application mode control types and DDC loop points S S POINT INTERLOCKS to 8 groups of points Circuit board is designed for mounting a NEMA 1 enclosure Mounts vertically in a controller enclosure ENC 001 mounts in a double controller enclosure ENVIRONMENT to 122 to 50 5 to 85 RH non condensing REQUIREMENTS 120Vac 15 50 60 Hz 0.25 Amp 240Vac 15 50 60 Hz 0.25 Amp 12.75 x 10.5 x 2.0 4 Ibs 6oz Weight 5 Ibs 4 oz ll ZOVAC SWITCH CONTROLLER CONTINUED PROTECTION AGAINST FIRE REPLACE WITH FUSE THE SAME TYPE AND RATING Circuit Board with Backplate 1 Guidelines GUIDELINES equipment has been tested and found to comply the limits for a Class digital device pursuant are designed Part 15 of the FCC rules These provide reasonable equipment operated equipment generates environment and can radiate radio frequency energy and if installed and used in accordance with the manual may cause harmful interference communications Operation of this equipment residential area the interference at his own expense which case the user will be required to likely to cause harmful a beginning the installation process for the DCM the unit for any obvious defects and to sure all parts are included any flaws are contact your local Siebe Environmental office or authorized INCLUDED IN THIS PACKAGE One Nl 1 110 DCM 1000 One N406 297 bag that includes the board KEP Nuts Nl OO 180136 3.6 V Nicad Battery End of Line Terminators ends of Connectors OO 410466 OO 5058 100 410464 one Nl OO 410502 REQUIREMENTS and the white wire to N eutral When wiring units connect the blackwire L ine the wire to E arth and the white wire to N eutral the 3 wire connector supplied with the DCM 1000 board a 3.6 Vdc Nicad battery provided bag that must be installed bottom right of board The battery provides backup for 72 hours in the event of a power Make sure the battery polarity is correct when the battery the Switch just above the power input connector switch for the DCM 1000 are clearly marked on the circuit board ON and OFF the just to the right of the On Off switch is a fuse containing a l 4 Amp slo blo fuse To replace push while turning fuse use a small screwdriver fuse holder counter clockwise fuse is spring and will pop ou