Invensys F-25715

lnvensys Building Systems Building Systems Inc Clifford Avenue Zip 6111 I Clifford Avenue Box 2940 Box 2940 Park IL 61132 2940 Park IL 61132 2940 States of America Sensors are digital room temperature used with the MicroNet 2000TM family of Available three models all MicroNet sensing and plug in communication for the MicroNet Controller computer software DOS based Sensors are suitable direct wall 2 x 4 box 114 DIN electrical box or surface box Chart Model Chart MN SDK Only Sensor Instructions in U S A 5 1 DOCUMENTATION Applicable Documentation 1 2000 2 Controller User Manual 3 4 Controller Air Balance MicroNet 7 MicroNet General Bus 8 Series MicroNet Controller VAV Controller Manual MicroNet General VAV Controller Manual Sales Personnel Application Engineers Application Engineers Start up Technicians Service Personnel Application Engineers Start up Technicians Service Personnel Application Engineers Start up Technicians Service Personnel Application Engineers Start up Technicians Service Personnel Application Engineers lnstallers Start up Technicians Service Personnel Application Engineers Start up Technicians Service Personnel Building Operators Application Engineers Start up Technicians Service Personnel Application Engineers Start up Technicians Service Personnel an introduction descriptions wiring practices and system architecture the product family Contains detailed tutorial startup and menu information and step by step Controller systems air balancing MicroNet step by step Module procedures the MicroNet step by step and checkout procedures the step by step VAV Controller and checkout procedures the MicroNet VAV Controller setup programming and software and the deluxe MicroNet Sensor includes diagnostic using both the MicroNet Controller step by step and checkout procedures the all pre engineered applications bills of material sequence of operation wiring the MicroNet VAV MicroNet Sensor parts packaged disassembled one container and consists of three A pre wirable base plate which includes a MicroNet communication An electronic assembly containing sensor and associated circuitry A removable cover the carton for possible damage the components damaged notify the appropriate carrier obvious damage Return damaged products wiring diagrams not provided Appropriate screwdrivers Digital Volt ohm meter DVM Level Drill and bits for mounting screws Wrist grounding strap wiring terminals and mounting screws must be a qualified experienced appropriate mounting screws not provided screw anchors for direct wall mount installations provided t 0 Appropriate accessories AT 504 AT 1104 AT 1155 AT 1163 MNA STAT 1 MNA STAT 2 MNA STAT 3 mounting base beige aluminum guard with steel base plate plastic guard with solid and ring base tumbler guard with steel base plate covers qty 12 for MN S model qty 25 for MN SO model qty 25 key lock Electrical shock hazard Disconnect power before prevent electrical or equipment damage Make all connections accordance with the electrical wiring diagram and in with national and local electrical codes Use copper conductors 75 are charges produce voltages high enough microprocessor and associated circuitry within the MicroNet Sensor are extremely or operating static discharge Follow static electricity precautions when installing electronic components system damage in a static free area any static electricity you may have accumulated Discharge static electricity touching a known securely grounded object a wrist strap when handling clamp must be secured to earth ground MicroNet Sensor electronic assembly The wrist Communications Commission Part 15 of the FCC Rules These limits are designed This equipment has been tested and found to comply with the limits for a Class A provide device pursuant protection against harmful a environment This equipment generates uses and can radiate radio frequency and if not installed and used in accordance with the instruction manual may cause interference a residential is likely to cause harmful interference which case the user will be required to correct interference at his own expense radio communications Operation of this equipment when the equipment operated Department of Communications digital apparatus does not exceed apparatus set out in the radio interference Class A limits for radio noise emissions of the Canadian Department of Avoid locations where excessive moisture corrosive explosive vapors or present Avoid electrical noise interference Do not install near large contactors electrical or welding equipment MicroNet Sensors are intended indoor use only Locate where ambient do not exceed 122 50 or fall below 32 0 and relative does not exceed 95 or fall below 5 non condensing the MicroNet Sensor on an inside wall where the room ft minute minimum which represents space The location should be out of direct sunlight away from sources of heat or cold away from concealed ducts or pipes will be exposed average unrestricted air Sensors can be direct wall 2 x 4 electrical box l 4 DIN electrical box or surface mounted Refer to Figure l and Figure 2 for appropriate mounting method dimensions Mounting Dimensions Direct wall 2 x 4 Electrical Box Surface Box Mounting A shown in inches mm Mounting Dimensions l 4 DIN Electrical Box Mounting Mount direct wall mounting the mounting dimensions shown in Figure l drywall anchors as necessary the two U Link wires from the wall through base plate feedthrough two appropriate screws not provided mount the base plate to the wall Direct wall Mounting x 4 Electrical Box Mount