Invensys MSC-U1000 Unit Controller

MSC Ul 000 Unit Controller in U S A OF CONTENTS GUIDELINES INCLUDED THIS PACKAGE AND ACCESSORIES REQUIREMENTS and EMI Grounding Grounding AND SETUP WIRING JUMPERS AND INDICATORS MSC Ul SUPPORT Outputs Start up The Database can be used as either a MSC Ul 000 MicroSmart Unit Controller is for Direct Digital Control DDC of a air handling unit or other mechanical with a single controller package MSC Ul controller or with the Robertshaw Management System DMS When used communications are obtained the Robertshaw Handheld Operator MSC HOI A portable PC used in with the Laptop Interface Module also provides communications to the When used with the DMS is via a two wire RS 485 trunk to Figure 1 for details controller provides ten analog inputs that are for 1000 ohm platinum or Balco sensors 4 20 mA inputs or contact four SPDT contact outputs load override are provided for two of these contact and two contact inputs to be used for or pulse monitoring trend data feature permits trending of all for up to 72 samples by their maximum average or current values The feature having two schedulable events for ten days assignable to any point that can commanded to start or stop provides full capability Each points can be to one of these schedules and defined be the primary schedule or a backup schedule NO MSC UlOOO for 12OV 50 60 Hz OOO I for 24OV 50 60 Hz GENCY LISTINGS UL 916 Equipment UL 873 Indicating and Regulating pending Complies with FCC Class requirements CAPACITY Maximum of 64 points 32 of may be extended record up to 5 auto tune A0 points AO MC All points 72 readings for each point time default 1 hour Trend MAX MIN or VALUE Installation Guidelines Assignable to any schedulable 2 schedules 10 days 6 events day or backup mode PROGRAMMING code available 10 UDPs max lines of INHIBITING User programmable S S up to 255 seconds following start analog input and loop points up to minutes with alarm delay capability One 2 wire RS 485 serial to 4000 feet 51.2K baud WIRE Under 1000 Belden 9501 to 4000 Belden 9823C riser under 1000 Belden 89503 riser up to 4000 Belden 89182 INPUTS 10 inputs individually for any of the following Ohm Platinum Temoerature Sensor 40 240 F 0.1 o F resolution 40 to 115 C 0.06 C resolution to F 0.1 F resolution 33.6 to 115 C 0.06 C resolution mA 0.01 mA resolution GUTPUTS 4 SPDT each with LED 2 with override switch Position of switch is monitored RATINGS non inductive 3 amps 24Vac or Vdc l amp 120Vac 5 amp INPUTS 2 for status or pulse of dry contacts Maximum pulse rate 5 Hz 40 60 duty cycle OUTPUTS Slots for up to 5 optional output cards for either electric or outputs 18 l 2 x 1 l 1 2 x 3 REQUIREMENTS 12OV 50 60 Hz max 24OV 50 60 Hz 50W max BACKUP 72 hr battery for database and clock backup ENVIRONMENT 32 to 122 0 to O 90 RH non condensing 7 Ibs 12 oz weiaht 8 Ibs 4 oz GUIDELINES equipment has been tested and found to with the limits for a Class digital pursuant to Part 15 of the FCC rules limits are designed to provide reasonable against harmful interference when the is operated in a commercial This equipment generates uses can radiate radio frequency energy and if not and used in accordance with the manual may cause harmful to radio communications Operation this equipment in a residential area is likely to harmful interference in which case the user be required to correct the interference at his expense beginning the installation process for the visually inspect the unit for any defects and to make sure all parts are If any flaws are detected contact your Robertshaw office or authorized immediately information is contained in this For further details regarding software please refer to the DMS Operator User Guide and the MicroSmart Interface User Guide THIS Controller INCLUDED One Nl 1 119 MSC Ul One N406 279 hardware bag that includes following ea 6 KEP nuts NlOO 180136 ea 4 position connectors N100 410464 ea 6 position connectors N100 410466 ea 3 position connector green N100 410502 ea 1 O position connectors ea 3 position connector orange 100 410432 of labels N100 430243 ON AUTO OFF ea battery Nl OO 5058 OO 410506 000 Guidelines AND ACCESSORIES following accessories can be used with the but must be ordered separately and TS 58000 series platinum RTD thermostats and remote sensors and and TS 81000 series Balco See separate platinum RTD room data sheet for special models using jacks adjustable setpoints and overrides Operator Interface MSC HOI Interface Module MSC LIM for use a personal computer the upper right corner of the 000 are five option slots Each of slots will accept one of several analog option cards Each of these cards a single variable output The available include Output MSC UC PO which a O l 5 psig signal for controlling actuators and damper motors For information on the MSC UC PO please refer to its installati